Bedienungsanleitung Whirlpool Hollywood 1400 (Seite 2 von 2) (Englisch)

71303

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 10346

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 49* 1.90 2:00

Cotton** 60 5.0 49 0.95 2:20

Cotton 40 5.0 49 0.60 2:00

Synthetics 60 2.5 50* 0.70 1:30

Synthetics 40 2.5 45 0.55 1:15

Delicates 30 1.5 50 0.50 0:45

Quick wash 30 3.0 40 0.40 0:30

Wool 40 1.0 55 0.60 0:45

Handwash 40 1.0 45 0.60 0:40

Handwash 30 1.0 45 0.50 0:40

Add detergents as indicated on the front page and as

described in your Instructions for Use. Close the door

and turn the programme selector to the desired

programme and temperature. The indication lamp next

to the “Start/Pause” button flashes.

CONSUMPTION DATA

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the

home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type

of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water

out.

** Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the door can be opened. As long

as a wash programme is running, the door remains

locked and must on no account be forced open.

In case you have an urgent need to open it during a

running programme, refer to “Cancel (Reset) a running

programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Push the button(s) of any option(s) desired - the

respective indication lamp lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

“Cold wash” button

• With this option, water is heated only up to 20ºC.

• Suitable for delicate laundry items with wash

temperature recomendation of max. 30ºC on the

care label.

• Selectable only on the lowest temperature step of

each programme.

“Spin speed reduction” button

• Reduces the predetermined automatic maximum

spin speed to treat your laundry more gently.

Whirlpool is a registered trademark of Whirlpool USA.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

When the programme phrase is finised, the

corresponding indication goes out.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature), any

options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end.

• Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door

can be opened.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool Hollywood 1400 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool Hollywood 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info