5019 301 05965
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the
programme selector
to the desired
programme. The display shows the programme
duration in hours and minutes as well as the
predefined temperature. The
“Start/Pause”
button flashes.
2. The
temperature
can be altered by pressing
the “Temperature” button.
3. The indication lamp of the predefined
spin speed
lights up; in case you want to set another spin
speed, press the “Variable spin” button .
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only for heavi ly soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid deterge nt for the main wash
when activating the Prewash option.
“Easy ironing” button
• Can be used together with “Cotton ”,
“Synthetics” and “Daily load” programmes to
make ironing easier .
• Increases the water quantity and the clothes are
spun very gently .
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water , washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only .
• If you select “Rinse hold”, do not leave the laundry
to soak for too long.
Note:
The programme stops to “Rinse hold” at
the time the “Anticrease” light in the programme
sequence indicator is on. The indication lamp
next to the
“Start/P ause”
button flashes.
T erminate the “Rinse hold” option :
• P ress the
“Start/Pause”
button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
CONSUMPTION DATA
Programme
T emperature
(°C)
Load
(kg)
W ater
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
*
White Cotton 95 6.0 59
**
1.90 2:00
Cotton 60 6.0 49 1.14 2:10
Cotton with “Eco”
***
60 6.0 49 1.02 2:20
Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 30 1.5 60 0.50 0:45
Quick wash 40 3.0 41 0.50 1:00
Delicates 30 3.0 41 0.40 0:30
W ool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Stan dard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type o f wa sh .
*
The time indicated on the display can deviate fro m the values in the table, because it takes into account the household
conditions applicable at that time.
**
T o reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains t he water out .
***
Reference P rogramme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO N
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain ” programme
and press the
“Start/P ause”
button.
“ V ariable spin ” button
• Every programme has a predefined spin speed.
• P ress the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only .
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent
when activating the “Start delay”.
• Select programme, temperature and options.
• P ress the “Start delay ” button to select the delay
time by 1 to 23 hours;
• P ress the
“Start/P ause”
button.
The indication light next to the “Start delay ”
button lights up and the countdown of the delay
time begins. The dot between hours and
minutes of the delay time indicated flashes.
•T h e t i m e d e l a y i n d i c a t ion disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the
“Start/P ause”
button,
the number of hours preselected can be reduced
by pressing and holding the “Start delay ” button.
From 1 hour on, the delay time can also be
reduced in steps of 10 minutes.
T o cancel the “Start Delay ”
..before you press the “Start/P ause” button:
• T urn the programme selector to another
position or press the
“Reset”
button.
..after having pressed the “Start/P ause” button:
• Press the “R eset” button for at least 3 seconds - the
start delay time disappears from the display .
Open the tap and press the
“Start/P ause”
button. The
indication lamp next to the
“Start/P ause”
button lights
up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time.
Due to variations in load and temperature of inlet
water, the remaining time is newly calculated in certain
programme phases. If this is the case,
an animation
appears on the display
.
Before starting and after end of a programme, the
lamp lights to show that the door can be open ed. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• A ll the lights of the programme sequence
indicator are off , and the “Door open ”
indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry .
1. Press the
“Start/P ause”
button to pause the
programme. The light flashes.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the
“Start/P ause”
button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
The
“Reset”
button cancels a programme before
the end.
• P ress the
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PRO GR AMM E S TAR T
“DOOR OPEN” INDICATION
RED INDICA TIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30105965GB.fm Page 2 Tuesday, October 17, 2006 6:26 PM
Black process 45.0° 100.0 LPI