Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
Push the button of any option desired - the respective
indication lamp lights up. If the combination of
programme and additional option(s) is not possible, the
indication lights switch off automatically.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand
or granular dirt).
•Do not use liquid detergent for the main wash when
activating the “Prewash” option.
PROGRAMME END
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause”button to pause the
programme. The light blinks.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the “Start/Pause”button again.
The new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
“Rapid” button
• Enables quicker washing by shortening the
programme duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
“Clean+” button
•Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with the maximum load.
• Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber,
together with your detergent (only use powder
detergent with this option). Respect the
manufacturer’s dosing instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Cold wash” button
• Saves energy used for water heating while maintaining
good wash result.
• Recommendable for lightly soiled laundry without
stains.
• Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of
the programmes.
START DELAY
Load the laundry, close the door and add detergents as
indicated on the front page and as described in the chapter
“Detergent and Additives” in your Instructions for Use.
Turn the programme selector to the desired programme
and temperature. The display shows the programme
duration and the predefined spin speed. The indication lamp
next to the “Start/Pause” button blinks.
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. Switch on the
washing machine again by turning the programme selector
back to “Off/O” and then to the desired programme.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and
a very gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
•The programme stops to “Rinse hold” at the time the
“Rinse hold” lights in the preogramme sequence
indication is on. The “Start/Pause” indicator blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme
and press the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set different spin speed.
•If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating “Start delay” option.
•Select programme, temperature and options.
•Press the “Start delay” button to select the desired
delay time up to 23 hours.
•Press the “Start/Pause” button.
On the display, the start delay symbol and the dot
between hours and minutes blink. The countdown of
the delay time begins.
•The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
•Once having pressed the “Start/Pause” button,
the delay time can be reduced by pressing again the
“Start delay” button.
To cancel the “Start delay”
...before you press the “Start/Pause” button:
• Turn the programme selector to another position or
press the “Reset” button.
...after having pressed the “Start/Pause” button:
• Press the “Start/Pause” button - the start delay time
disappears from the time display.
Whirlpool is a registered trademark of Whirlpool USA.
5019 300 00114
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
without “Rapid”with “Rapid”
Cotton/Antibacterial956.059**1.902:00-
Cotton606.0491.022:301:35
Cotton 406.0540.652:001:15
Jeans405.0690.632:151:30
Synthetics603.050**0.701:351:14
Synthetics403.0460.501:200:59
Delicates401.5500.650:50-
Delicates301.5500.500:46-
Daily load403.0450.451:00-
Quick wash303.0400.300:30-
Wool/ Handwash401.0450.600:40-
Wool/ Handwashcold1.0450.100:35-
Cotton *606.0490.784:00-
Cotton *603.0370.692:20 ***-
Cotton *403.0370.582:30-
FAILURE INDICATIONS
The “Reset” button cancels a programme before the
end.
•Press and hold the “Reset” button for a few seconds.
Any existing water is drained out. It may last
some time until the door can be opened.
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply
will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions
refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also
change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Power consumption in off-mode
0,16
W / in left-on mode
0,16
W
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet
water.
”Service”: failure or malfunction of an electrical
component.
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks : unbalance during
spinning.
PROGRAMME START
Open the tap and press the “Start/Pause”button.
The indication lamp next to the “Start/Pause”button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
In der Bedienungsanleitung steht hierzu: "Zum Öffnen des Sockels (je nach Modell): Drücken Sie die Laschen auf der rechten und linken Seite (falls vorhanden) nach unten, um die Sockelblende zu entriegeln und nehmen Sie sie ab (Abb. „A“). Ich fürchte nur, dass sie damit genauso wenig anfangen können, wie jeder andere, deren Maschine nicht über diese "Laschen" verfügt. Extrem ärgerlich, sowas.
Beantwortet 15-11-2020 at 11:32
Meine waschmaschine pumpt nicht ab es tut sich gar nichts....habe das sieb schon gereinigt den löschknopf gedrückt einfach alles ausprobiert...ich bin verzweifelt hilfe
Eingereicht am 16-12-201722:40
Hallöchen ich habe die Whirlpool Hotline 0711 / 8888 900 angerufen. Die haben mir sehr gut geholfen. Die Startvorwahl-Taste ist wirklich für die Startzeit zuständig. Programm wählen und dann die Startstunden einstellen, dabei kein flüssiges Waschmittel benutzen, sondern Pulver.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Whirlpool Primo 1406 UM wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
