Bedienungsanleitung Whirlpool pure 1400 7 (Seite 2 von 2) (Englisch)

308350

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 06274

Whirlpool is a registered trademark of Whirlpool USA

Load your laundry, close the door properly and add detergent

as indicated on the front page and as described in the chapter

“Detergent and Additives” in your Instructions for Use.

1. Turn the

programme selector

to the desired

programme. The display shows the programme

duration in hours and minutes as well as the predefined

temperature. The

“Start (Pause)”

button blinks.

2. The

temperature

can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined

spin speed

lights up; in case you want to set another spin speed,

press the “Variable spin” button.

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and option is not

possible, the lights switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Clean +” button

• Choose this option if you use an in-wash additive for

stain removal (powder, for example “Vanish”) - it will

optimize the additive’s efficiency to get better wash

performance and stain removal.

• Choose temperature of 30 or 40°C and use with

maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together

with your detergent (only use powder detergent with this

option). Respect the manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15 minutes.

• Appropriate for use of stain removers and bleaches on

oxygen basis.

Chlorine or perborate bleaches must

not be used!

“Easy ironing” button

• Helps to make ironing easier.

• Increases the water quantity and the clothes are spun

very gently.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helping people with

allergies.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the final spinning is

cancelled but intermediate spin peaks remain during

rinse. The water is drained out only.

•If you select

“Rinse hold”

, the laundry remains in the

last rinse water without progressing to the final spin

cycle to avoid creasing and prevent colours from

changing.

-Select

“Rinse hold”

if you want to postpone

spinning to a later time or if you want to drain only.

- Do not leave the laundry to soak in the rinse hold

for too long.

- The programme stops to “Rinse hold” when the

“Rinse hold” light in the programme sequence

indicator is on; the “Rinse hold” light of the

“Variable spin” button and the

“Start (Pause)”

button

light blink.

-To terminate the “Rinse hold” by draining the

water, without any spinning, press the

“Start

(Pause)”

button.

- To terminate the programme by spinning the

laundry, press the “Variable spin” button to select

the desired spin speed and then the

“Start

(Pause)”

button to start the spin cycle.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton / Antibacterial 95 7.0 74

2.10 2:10

Cotton

***

60 7.0 54 1.19 2:20

Cotton 40 7.0 69 0.75 2:05

Synthetics 60 3.5 46

0.85 1:35

Synthetics 40 3.5 42 0.50 1:20

Delicates 30 2.5 60 0.40 0:45

Wool 40 2.0 60 0.60 0:45

Handwash 40 2.0 45 0.60 0:40

Jeans 40 7.0 86 0.75 2:21

Big Items 40 3.0 74 0.75 1:30

Sport 30 3.5 54 0.55 1:34

SuperEco 60 7.0 69 0.84 4:00

Daily load 40 6.0 73 0.60 1:00

Speed 15 30 3.0 30 0.20 0:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary

with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating the “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select a delay time up to

23 hours; the light of the

“Start (Pause)”

button blinks.

• Press the

“Start (Pause)”

button; the countdown of

the delay time begins. The light of the

“Start

(Pause)”

button is on; the light of the start delay

button will keep blinking until the programme starts.

• As soon as the programme starts, the start delay on

the display is replaced by the remaining programme

time, and the light of the “Start delay” button goes off.

• Once having pressed the

“Start (Pause)”

button, the

number of hours preselected can be changed by

pressing and holding the “Start delay” button.

To cancel the “Start delay”

..before you press “Start (Pause)”:

• Turn the programme selector to another position or

press the

“Reset/Drain”

button.

..after having pressed “Start (Pause)”:

• Press

“Start (Pause)”

- the delay time disappears

from the display; press

“Start (Pause)”

again to start

the selected programme immediately.

Open the tap and press

“Start (Pause)”

; the light stops

blinking and is on. The programme sequence indicator

shows the current programme phase, running from left to

right through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is

the case,

an animation appears on the display

Activating the child lock prevents children from starting a

wash cycle or changing the settings of a running programme.

The child lock cannot be activated or deactivated when the

programme selector is in the “Off/O” position. To activate

the child lock:

• Turn the programme selector to a programme

position, or run a programme as usual.

• Press the 2 buttons marked with the key

symbol simultaneously for at least 3 seconds; a

key-like symbol will shortly appear on the display to

indicate that the child lock is active.

Any time you try to change a programme setting with

active child lock, the display will shortly show the key-like

symbol. The programme setting cannot be changed

anymore; the only change possible is to switch the washer

off by turning the programme selector to the “Off/O”

position. To deactivate the child lock:

• Press again the 2 buttons marked with the key

symbol simultaneously for at least 3 seconds.

Before starting and after end of a programme, the lamp

lights to show that the door can be opened. As long as a

wash programme is running, the door remains locked and

must on no account be forced open. In case you have an

urgent need to open it during a running programme, refer

to “Reset a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a

fault in an electrical component. Refer to the

“Troubleshooting Guide” in your Instructions for Use; if

the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain

hose is kinked or the filter must be cleaned; in the latter case

refer to the Instructions for Use (“Removing the Filter”).

• The display shows “End” and the “Door open”

indication lights.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press

“Start (Pause)”

to pause the programme; the

light blinks.

2. Select the new programme, temperature, any options

and another spin speed if you want.

3. Press

“Start (Pause)”

again. The light is on, and the

programme continues continues at the same position

where the previous programme was interrupted. Do

not add detergent for this programme.

The

“Reset/Drain”

button cancels a programme before

the end.

• Press the

“Reset/Drain”

button for at least 3

seconds; “rES” appears on the display. Any existing

water is drained before the door can be opened.

START DELAY

PROGRAMME START

CHILD LOCK

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

30106274GB.fm Page 2 Tuesday, April 7, 2009 12:42 PM

Black process 45.0° 150.0 LPI

Whirlpool pure 1400 7 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool pure 1400 7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info