5019 301 06279
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
button blinks. The
temperature
and
spin
speed
indicated on the display can be altered by pressing the
“Temperature” button or the “Variable spin” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Prewash” button
• Only for heavily soiled loads example sand, granular dirt)
sensible. Increases the cycle time
• Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Clean+” button
• Choose this option if you use an in-wash additive for stain removal
(powderanish”) - it will optimiz
efficiency to get better wash performance and stain r
• Choose temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minut
• Appropriate for use of stain
basis.
Chlorine or perborate bleaches must
“Easy ironing” button
• Makes ironing easier by an increased water quantity and a very
gentle spin.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The w
drained out only
• If you select “Rinse hold” , the laundry remains in the last
rinse water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Variable spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
- The wa
“Rinse hold” symbol on the d
“Start (Pause)”
button blinks as well.
- To terminate the “Rinse ” by draining the water,
without any spinning, press the
“Start (Pause)”
button.
- To terminate the “Rinse by spinning the laund
the “Variable spin” button to select the desired spin speed
and then
“Start (Pause)”
to start the spin cycle.
- Do not leave the laundry to soak for too long in the “Rinse hold”.
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
pr
CONSUMPTION DATA
Programme
Te m p e r a t u r e
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton 95 8.0 82
**
2.40 2:10
Cotton
***
60 8.0 59 1.36 2:20
Cotton 40 8.0 77 0.75 2:05
Synthetics 60 3.5 46
**
0.85 1:35
Synthetics 40 3.5 42 0.50 1:20
Delicates 30 2.5 60 0.40 0:45
W 40 2.0 60 0.60 0:45
Handwash 40 2.0 45 0.60 0:40
Jeans 40 7.0 95 0.80 2:21
Big Items 40 3.0 74 0.75 1:30
Sport 30 3.5 54 0.55 1:34
SuperEco 60 8.0 75 0.95 4:00
Daily load 40 6.0 73 0.60 1:00
Speed 15 30 3.0 30 0.20 0:15
Consumption values were measurin normalized conditions in compliance with Standard IEC/ENe
may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of
*
The time indicated on the display can deviate from the valons
applicable at that time.
**
Tend of the main wash cycle, before the pump drains the water
out.
***
Reference P
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
SA
• Sele
option(s), push and hold the
“Favourites”
button for at least
3 seconds. The lamp next to
“Favourites”
shortly blinks and
then lights up - the programme setting is saved.
Next time you want to use
select the programme, push the
“Favourites”
button and start by
pushing
“Start (Pause)”
.
If you want to replace the saved programme setting by
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for exawhen electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
• Sele
• Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•P
“Start (P
button.
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
T
..before you press the “Start (P
• Press the
“Reset / Drain
button, or set the start delay time to
“0:00” - the delay time disappears after a few seconds.
..after having pressed the “Start (Pause)” button:
Press th
“Reset/Drain
button for at least 3 seconds; the start
delay time disappears from the display
“Start (Pause)”
twice to start the selected programme immediately
Before starting a programme, the symbol lights to show that the
door can be opened to
“Start (P
, the door will lock until the end of the
programme and must on no account be forced open. In case you
have to open it urgently during a running programme, refer to
“Reset a running programme before the end”.
If you try to start a wa
closed, the “Add garment” indication will blink.
Open the tap and press the
“Start (P
button; the blinking
“Start (P
button light becomes constant. The “Add
garment” indication goes out, and the lit bubbles indicate that the
programme is in process. In some phases,
programme time is newly calculated - if th
th
sense” indication on the display will fade, and the remaining
programme time is replaced by an animation.
Activating the child lock prevents children
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated wh
selector is in the “Off/O” position. To activate the child lock:
• Turn the programme selector to a programme position, or run
a programme as usual.
• Press the “Temperature” and the “Variab
simultaneously for at least 3 seconds. The “Child lock” symbol
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
• T
indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
• Leave the door ajar to allow the drum to dry.
• If you do not turn the programme selector to the “
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain on the display
The symbol will blink at the end of the programme if you used too
much detergent. Use less detergent next time.
1. Press the
“Start (P
button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start (P
button again. The new
programme continues at the same
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset/Drain”
button cancels a programme before the end.
• Pre
“Reset/Drain
button for at least 3 seconds;
animation appears
out before the door can be opened.
START DELAY
“
PROGRAMME START
CHILD LOCK
RED FAIL
PROGRAMME END
DETERGENT OVERDOSA
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
