Bedienungsanleitung Whirlpool TDLR 70230 (Seite 4 von 16) (Englisch)

641522

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN 2

5. EC Declaration of Conformity

• This washing machine has been designed,

constructed and distributed in compliance

with the safety requirements of EC Directives:

2006/95/EC Low Voltage Directive 2004/108/EC

Electromagnetic Compatibility Directive

The Manufacturer is not liable for any damage to

laundry resulting from inadequate or incorrect fabric

care instructions which have been provided with the

garment or article.

BEFORE USING THE WASHING MACHINE

1. Remove the packaging and check

a. Cut and remove the shrink-wrap.

b. Remove the top protection and the protective

corners.

c. Remove the bottom protection by tilting and

turning the washing machine on one rear

bottom corner. Make sure that the plastic part

of the bottom protection (if available on the

model) remains in the packing and not in the

machine bottom.

This is important, as otherwise the plastic part could

damage the washing machine during operation.

d. Open the lid by pressing it slightly down while

raising the handle. Remove the polystyrene

cushion (depending on model).

e. Remove the blue protective ﬁlm from the panel

(depending on model).

• After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local retailer.

• Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children;

they are potentially dangerous.

• If the appliance was exposed to the cold prior to

delivery, keep it at room temperature for a few

hours before operating.

2. Remove the transport bracket

• The washing machine is ﬁtted with transport

screws and a transport bracket to prevent damage

during transport. Before using the washing

machine you must remove the transport

bracket (see “Installation”/“Removal of transport

bracket”).

3. Install the washing machine

• Place the washing machine on a ﬂat and stable

ﬂoor surface.

• Adjust the feet to ensure that the machine is

stable and level (see “Installation”/“Adjust the

feet”).

• In case of wooden or so-called “ﬂoating ﬂoors” (for

instance certain parquet or laminate ﬂoors), place

the appliance on a sheet of plywood with a size of

at least 40 x 60 cm and thickness of at least 3 cm,

which is screwed to the ﬂoor.

• Make sure that the ventilation openings in the

base of your washing machine (if available on your

model) are not obstructed by a carpet or other

material.

4. Water supply

• Connect the water supply inlet hose in accordance

with the regulations of your local water company

(see “Installation”/“Connect the water inlet hose”).

• Water supply: Cold water only

• Tap: 3/4” threaded hose connection

• Pressure: 100-1000 kPa (1-10 bar).

• Only use new hoses for connecting the washing

machine to the water supply. Used hoses must not

be used anymore and should be discarded.

5. Drain hose

• Firmly connect the drain hose to the siphon or

another outlet for drain water. (see “Installation”/

Connect the water drain hose”).

• If the washing machine is connected to a built-in

drainage system, ensure the latter is equipped with

a vent to avoid simultaneous loading and draining

of water (siphoning effect).

6. Electrical connection

• Electrical connections must be carried out by a

qualiﬁed technician in compliance with the manu-

facturer’s instructions and the current standard

safety regulations.

• The technical data (voltage, power and fuses) are

given on the rating plate on the rear of the washing

machine.

• Do not use extension leads or multi sockets.

• Access to the mains plug or disconnection from

the mains supply via a double-pole switch must be

ensured at all times after the installation.

• Do not operate the washing machine if it has been

damaged during transport. Inform the After-Sales

Service.

• Mains cable replacement is only to be carried out

by After-Sales Service.

• The washing machine must be connected exclu-

sively by means of a socket with an earth connec-

tion, in compliance with the regulations in force. In

particular, washing machines installed in premises

containing a shower or a bath must be protected

by a differential residual current device of at least

30 mA. Earthing the washing machine is obliga-

tory under the law. The manufacturer declines all

liability for injury to persons or animals or damage

to property deriving either directly or indirectly from

failure to observe the directions in these Instruc-

tions for Use.

• When using a residual current circuit breaker

(RCCB), only use a model marked with .

Approximate dimensions:

Width: 400 mm

Height: 900 mm

Depth: 600 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool TDLR 70230 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool TDLR 70230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info