Bedienungsanleitung Whirlpool TDLR65230L BE (Seite 4 von 4) (Englisch)

793715

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

TROUBLESHOOTING

The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to check to see if

the problem can be easily resolved using the following list.

Anomalies: Possible causes / Solution:

The washing machine does not turn on

and/ or programme does not start

• The plug is not inserted into the electrical outlet, or not enough to make contact.

• There has been a power failure.

• Lid is not properly closed.

The wash cycle does not start.

• The “Start/Pause” button has not been pressed.

• The water tap is not open.

• A “Delay Timer” has been set.

Appliance stops during the

programme, and the “Start/Pause”

light blinks

• “Rinse hold” option is activated (if available).

• Programme has been changed - reselect desired programme and press “Start/Pause” .

Appliance vibrates

• The washing machine is not level.

• The transport bracket has not been removed; before using the washing machine, the transport

bracket must be removed.

Final spin results are poor. The laundry

is still very wet. “Spin” indicator blinks,

or the spin speed indicator blinks after

the end of the programme - depending

on the model

• Unbalance of the laundry load during spinning prevented the spin phase to avoid damages on

the washing machine. This is why the laundry is still very wet. Reason for unbalance can be:

small laundry loads (consisting of only few quite big or absorbent items, e.g. towels), or big/

heavy laundry items.

• If possible avoid small laundry loads.

• “Spin” button has been set to a low spin speed.

“Call Service” indicator lights up

• Shut o the machine, disconnect the plug from the outlet, and wait about 1 minute before

turning it back on.

• If the problem persists, call the After-sales service.

“Water lter clogged” indicator

lights up

• Waste water is not pumped out.

• Clean the water lter

“No water” indicator lights up • Appliance has no or insucient water supply.

All lamps of the

Washing phase indicator lights up

• Drum aps open

• Appliance stops during the programme. The drum aps have not been closed properly. Push

the “Reset” button button for at least 3 seconds and wait until the “Lid open“ light turns

on. Open lid and close drum aps, then select and start desired programme again. If fault

persists, contact our After-sales service.

XXXXX

Regulatory documentation, standard documentation, ordering spare parts and other product information can be

found:

• By visiting our website docs .whirlpool. eu and parts - selfservice .whirlpool. com

• Using QR Code

• Alternatively, contact our After-Sales Service (See phone number in the warranty booklet). When contacting our

After-sales Service, please state the codes provided on your product’s identication plate.

For User Repair & Maintenance Information visit www.whirlpool.com

The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model

identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool TDLR65230L BE Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool TDLR65230L BE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info