Bedienungsanleitung Whirlpool WAGHID83F (Seite 1 von 3) (Englisch)

702423

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Quick guide

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT

In order to receive a more complete assistance, please

Before using the appliance carefully read the Safety

Instruction.

PRODUCT DESCRIPTION

FIRST TIME USE

AIR VENT (FOR THE SUCTION VERSIONS)

Connect the hood and discharge holes on the walls with a diameter

equivalent to the air outlet (connection ange).

Using the tubes and discharge holes on walls with smaller dimensions

will cause a diminution of the suction performance and a drastic

increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! The company declines any responsibility whenever these regulations

are not respected.

FILTERING OR DUCTING?

! Your cooker hood is ready to be used in suction version.

To use the hood in ltering version the special ACCESSORY KIT must be

installed.

Check if the ACCESSORY KIT is furnished or must be bought separately.

Note: If furnished, in certain cases, the additional activated carbon ltering

system may be installed on the hood. Information about the conversion of

the hood from suction version to ltering version is present in the Manual

“Safety Instructions & Installation”.

DUCTING VERSION

In this case the fumes are conveyed outside of the building by means

of a special pipe connected with the connection ring located on top of

the hood.

Attention! The exhausting pipe is not supplied and must be purchased

apart. Diameter of the exhausting pipe must be equal to that of the

connection ring.

Attention! If the hood is supplied with active charcoal lter, then it

must be removed.

FILTER VERSION

The aspirated air will be degreased and deodorised before being fed

back into the room.

In order to use the hood in this version, you have to install a system of

additional ltering based on activated charcoal.

CONTROL PANEL

T1. ON/OFF button “Automatic operation

(sensor)” - see the function list in the

next paragraph

T2. Suction speed (power) control button:

1, 2, 3, intensive

Note: Intensive speed lasts for about 5

minutes, then it is automatically set to

speed 2.

T3. ON/OFF button (short press) and light

intensity setting (long press).

CAUTION! This hood has an automatic operation system (see

paragraph "Automatic operation (sensor)").

Calibration occurs automatically each time the hood is reconnected

to the electrical network (e.g.: the rst time it is installed after a

blackout). It can also be performed manually (see paragraph "Setting

of parameters for Automatic Operation - Manual setting").

During calibration, which lasts for 5 minutes, the controls will ash and

only the lights button can be used.

FILTER SATURATION INDICATOR

The hood signals when necessary to perform lter maintenance:

Grease lter (every 40 hours of use): all Leds with red light.

Activated charcoal odour lter (every 160 hours of operation): all

LEDs with red light, LEDs L2 and L3 blink.

RESET FILTER SATURATION

After performing lter maintenance, press and hold buttons T1 and T3,

Leds L1, L2 and L3 blink briey in red and then turn o for good.

• Activation indicator for odour lter saturation with activated

charcoal: This indicator is normally disabled. To enable it, proceed

as follows:

With the hood o, press and hold simultaneously T1 and T2: L1

turns on rst, then L2 and L3 and after that, when the buttons are

released, the Leds L2 and L3 ash briey to indicate successful

activation.

• Disabling the LED for charcoal lter saturation: repeat

the operation above; rst the LEDs L1, L2 and L3 turn on

simultaneously, then only L1, and after that, when the buttons

are released, the leds L1, L2 and L3 turn on again to indicate

successful disabling.

AUTOMATIC OPERATION SENSOR

CAUTION! We recommend running the “Automatic operation

settings” procedure (see below) before running the unit in automatic

mode.

AUTOMATIC OPERATION SENSOR

The hood will turn on at the speed most suited to the cooking

conditions detected by its sensor.

To activate this function:

Press button T1 briey, LED L1 will turn on white.

PARAMETER SETTING FOR AUTOMATIC OPERATION

Parameter setting duly takes place automatically whenever the hood

is connected to the mains (for example: with the rst installation or

after a power cut) or manually.

Note: All the manual operations of calibration, selection, setting and

logical connection described below are possible with the hood OFF

and automatic operation OFF (T1 OFF- L1 OFF).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WAGHID83F Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WAGHID83F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info