702377

Whirlpool WHVS90F Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/5
Nächste Seite
T8. AUTOMATIC “COOKSENSE” FUNCTION
The hood will automatically set an extraction speed of 1, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the hood is using extraction speed 1 and there is no change in the
ambient conditions, it will switch o after 5 minutes.
NB: to make sure this function is used correctly, please congure the
parameters for automatic mode rst as described in the relevant section.
NB: if you change any other speed control functions while automatic
mode is active, the auto ventilation function will switch o.
T9. FILTER SATURATION INDICATOR
At regular intervals, the hood signals the need to perform lter
maintenance.
Please note: The indicators will only work when the hood is on.
T9 button lit: carry out maintenance on the grease lter.
T9 button ashing: carry out maintenance on the carbon lter.
Resetting the lter saturation indicators:
Please note: This must be done with the hood switched on.
Press and hold the T9 button. The light will switch o to conrm the
reset.
Activating the carbon lter saturation indicator.
Please note: This must be done with the extraction motor switched o.
This indicator is normally deactivated. It should be activated if the
hood is installed in the ltering version (i.e. with carbon lters).
Press and hold buttons T1 and T10 simultaneously to activate the
function. The buttons will light up to indicate activation.
To deactivate the function, press and hold the same buttons (T1 and
T10) again. The buttons will ash briey and then switch o to indicate
deactivation.
T10. ON/OFF “BREATH DAILY CYCLE”
The hood will automatically set an extraction speed of 1, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the extraction speed does not change owing to the ambient
conditions detected, the hood will switch o after two hours.
The hood will switch o in any case after ve hours in use, regardless of
the operating mode.
Please note: to make sure this function is used correctly, please congure
the parameters for automatic mode rst as described in the relevant
section.
T11. ON/OFF “BREATH INTENSIVE CYCLE“
The hood will automatically set an extraction speed of 5, and then
increase it if necessary (according to the ambient conditions detected
by the hood sensor).
If the extraction speed does not change owing to the ambient
conditions detected, the hood will switch o after two hours.
The hood will switch o in any case after ve hours in use, regardless of
the operating mode.
Please note: to make sure this function is used correctly, please congure
the parameters for automatic mode rst as described in the relevant
section.
T12. LIGHT INDICATOR FOR WIFI FUNCTION ACTIVE
The indicator comes on when the hood is controlled from a distance
via the app.
T13. WIFI CONNECTION
Press to activate/deactivate the WI-FI functions.
This function allows the hood to be connected to the Internet so you
can monitor/control it from a distance via a smartphone or tablet.
To use the WI-FI function, connect the appliance to the domestic
wireless network (Internet) following the conguration procedure
explained in the “WI-FI MANUAL”.
CONFIGURING THE PARAMETERS FOR AUTOMATIC MODE
To make sure that automatic mode is used correctly, you will need to
calibrate the hood and select the hob type.
Calibrating the hood
NB: this must be done with the appliance on standby - i.e. one minute after
switching o the motor.
Press and hold the T4 button for ve seconds.
Extraction speed 1 will be activated and the T4 button will ash to
indicate that hood calibration has started (this will take approx. 5
minutes).
Please note: To stop the calibration process, press and hold the T4 button
for ve seconds. Calibration will then be invalidated and will therefore
need to be repeated.
Please note: Calibration will be carried out automatically when the power
supply to the product is switched on for the rst time. T4 will ash. Wait 5
minutes for the calibration to be completed.
Selecting the hob type
NB: this must be done with the appliance on standby - i.e. one minute after
switching o the motor.
Press and hold the T10 and T11 buttons for ve seconds.
The T10 and T11 buttons will light up.
If using gas to power the hob, press the T10 button – the button will
ash to indicate that this has been selected.
If using electricity to power the hob, press the T11 button – the button
will ash to indicate that this has been selected.
Once pressed, the button will ash for three seconds to indicate that
your selection has been saved.
TECHNICAL DATA
Height (cm) Width (cm) Depth (cm) Ø of exhaust tube (cm)
105 -148.6 89.8 36.9 15 - 12.5 - 12
CLEANING AND MAINTENANCE
CLEANING
• Do not use steam-cleaning equipment.
• Disconnect the appliance from the mains.
Important: do not use corrosive or abrasive detergents. If any such
products unintentionally come into contact with the appliance, clean
the appliance immediately with a damp cloth. Do not use alcohol.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few
drops of washing-up detergent to the water. Finish o with a dry
cloth.
Important: do not use abrasive sponges or metallic scrapers or
scourers. Over time, these can ruin the enamel surfaces.
• Use detergents specically designed for cleaning the appliance
and follow the manufacturer's instructions.
Important: clean the lters at least once a month to remove oil and
grease residue.
MAINTENANCE OF THE GREASE FILTERS
This must be cleaned once a month (or when the lter saturation
indication system - if envisaged on the model in possession - indicates
this necessity) using non aggressive detergents, either by hand or in the
dishwasher, which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease lter may discolour slightly,
but this does not aect its ltering capacity.
Open the extractor panel (turn upwards).
Please note: It is not necessary to remove the panel.
Pull out the handle to remove the lter.
Once the lter has been washed and left to dry, proceed in reverse
order to ret the lter.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool WHVS90F wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Whirlpool WHVS90F

Whirlpool WHVS90F Bedienungsanleitung - Deutsch - 5 seiten

Whirlpool WHVS90F Bedienungsanleitung - Holländisch - 5 seiten

Whirlpool WHVS90F Bedienungsanleitung - Französisch - 5 seiten

Whirlpool WHVS90F Bedienungsanleitung - Spanisch - 5 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info