Bedienungsanleitung Whirlpool WIP4O32 (Seite 9 von 12) (Englisch)

702760

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

INSTALLATION

ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back.

CONNECTING THE WATER SUPPLY

Adaptation of the water supply for installation should only be

performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards the right

or the left in order to achieve the best possible installation.

Make sure the dishwasher does not bend or squash the hoses.

CONNECTING THE WATER INLET HOSE

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn on the tap.

If the inlet hose is not long enough, contact a specialist store or an

authorised technician.

The water pressure must be within the values indicated in the Technical

Data table - otherwise the dishwasher may be function properly.

Make sure the hose is not bent or compressed.

SPECIFICATIONS FOR THE CONNECTION OF THE WATER SUPPLY

HOSE:

CONNECTING THE WATER OUTLET HOSE

Connect the outlet hose to a drain duct with a minimum diameter of

2cm A.

The outlet hose connection must be at a height ranging from 40 to

80 cm from the floor or surface where the dishwasher rests.

Before connecting the water outlet hose to the sink drain, remove the

plastic plug B.

ANTI-FLOODING PROTECTION

Anti-flooding protection. To ensure floods do not occur, the

dishwasher:

- is provided with a special system which blocks the water supply in the

event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety device

New Aqua Stop, which guarantees anti-flooding protection even in

the event of a supply hose rupture.

Under no circumstances should the water inlet hose be cut as it

contains live electrical parts.

ELECTRICAL CONNECTION

WARNING: Under no circumstances should the water inlet

hose be cut as it contains live electrical parts.

Before inserting the plug into the electrical socket, make sure that:

•The socket is earth and complies with current regulations;

• The socket can withstand the maximum load of the appliance as

shown on the data plate located on the inside of the door (see

PRODUCT DESCRIPTION).

• The power supply voltage falls within the values indicated on the

data plate on the inside of the door.

• The socket is compatible with the plug of the appliance.

If this is not the case, ask an authorised technician to replace the plug

(see AFTER-SALES SERVICE). Do not use extension cables or multiple

sockets. Once the appliance has been installed, the power supply cable

and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced by the

manufacturer or its authorised Technical Assistance Service in order to

prevent all potential hazards.

The Company shall not be held responsible for any incidents, if these

regulations are not observed.

POSITIONING AND LEVELLING

1. Position the dishwasher on a level sturdy floor. If the floor is uneven,

the front feet of the appliance may be adjusted until it reaches a

horizontal position. If the appliance is levelled correctly, it will be

more stable and much less likely to move or cause vibrations and

noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive transparent strip

under the wooden shelf in order to protect it from any condensation

which may form.

3. Place the dishwasher so that its sides or back panel are in contact

with the adjacent cabinets or the wall. This appliance can also be

recessed under a single worktop.

4. To adjust the height of the rear foot, turn the red hexagonal bushing

on the lower central part at the front of the dishwasher using a

hexagonal spanner with an opening of 8 mm. Turn the spanner in a

clockwise direction to increase the height and in an anticlockwise

direction to decrease it.

DIMENSIONS AND CAPACITY:

WATER SUPPLY cold or hot (max. 60°C)

WATER INTAKE 3/4”

POWER OF WATER PRESSURE 0,05 ÷ 1 MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

MIN 40 cm

MAX 80 cm

WIDTH 598 mm

HEIGHT 820 mm

DEPTH 555 mm

CAPACITY 14 standard place-settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WIP4O32 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WIP4O32

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info