Bedienungsanleitung Whirlpool WIP4O41PLEG (Seite 10 von 12) (Englisch)

756927

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

TROUBLESHOOTING

PROBLEMS POSSIBLE CAUSES SOLUTIONS

Salt

indicator is lit

Salt reservoir is empty. (After rell the salt indica-

tor may remain lit for several wash cycles).

Rell reservoir with salt (for more information - see page 2).

Adjust water hardness - see table, page 2.

Rinse aid

indicator is lit

Rinse aid dispenser is empty. (After rell the rinse

aid indicator may remain lit for several wash cycles). Rell dispenser with rinse aid (for more information - see page 3).

The dishwasher

won’t start or does

not respond to

commands.

The appliance has not been plugged in properly. Insert the plug into the socket.

Power outage. For safety reasons, dishwasher will not re-start automatically when power returns.

Open dishwasher door, press START button and close the door within 4 seconds.

The dishwasher door is not closed.

NaturalDry pin is not pulled in. Vigorously push the door until you hear the “click”.

Cycle is interupted by door opening for more

than 4 seconds. Press START and close the door within 4 seconds.

It does not respond to commands.

Display shows: F9 or F12 and all LEDs are blin-

king rapidly

Switch o the appliance by pressing the ON/OFF button, switch it back on after approxi-

mately one minute and restart the program. If problem persists, unplug the appliance for

1 minute, then plug it back in.

The dishwasher

won’t drain.

Display shows:

F3 and all LEDs are

blinking rapidly

The wash cycle has not nished yet. Wait until the wash cycle nishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The lter is clogged up with food residues. Clean the lter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes excessive

noise.

The dishes are rattling against each Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been produced.

The detergent has not been measured out correctly or it is not suitable for use in

dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by

switching OFF the dishwasher, then switch it on again, select a new program, press

START and close the door within 4 seconds. Please do not add any detergent.

The dishes are not

clean.

The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely, being hinde-

red by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been produced.

The detergent has not been measured out correctly or it is not suitable for use in dishwa-

shers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment has not

been shut correctly. Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

The dishwasher

does not ll the

water.

Display shows:

and F6 and all LEDs

are blinking rapidly

No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.

The inlet hose is bent. Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and

reboot.

The sieve in the water inlet hose is clogged; it is

necessary to clean it

After having carried out the verication and cleaning, turn o and turn on the dishwa-

sher and restart a new program.

Dishwasher nishes

the cycle prema-

turely.

Display shows: F15

and

all LEDs are

blinking rapidly

Drain hose positioned too low or siphoning into

home sewage system.

Check if end of drain hose is placed at correct height (see INSTALLATION).Check for

siphoning into home sewage system, install air admittance valve if necessary.

Air in water supply. Check water supply for leaks or other issues letting air inside.

The dishes have not

been dried

The selected program hasn’t any drying phase. Verify on the programs table if the selected program has the drying phase.

The rinse aid has run out or the resolution is not

adequate.

Add the rinse aid or adjust the dosage levels higher (see FILLING THE RINSE AID

DISPENSER).

The dishes are made of non-stick or plastic. It is normal the presence of drops of water (see TIPS).

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.

The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WIP4O41PLEG Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WIP4O41PLEG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info