Bedienungsanleitung Whirlpool WL B5860 AL (Seite 6 von 10) (Englisch)

793692

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

FIRST TIME USE

At the time of purchase, the hob is set to the maximum possible power.

Adjust the setting concerning the limits of your home's electrical system as

described in the following paragraph.

N.B: Depending on the power selected for the hob, some of the cooking zone

power levels and functions (e.g. boil or fast heating) could be automatically

limited to prevent the selected limit from being exceeded.

To set the power of the hob:

Once you have connected the device to the mains power supply, you can

set the power level within 60seconds.

Press the far right timer ”+” button for at least 5 seconds. The display shows

”PL”.

Press the

3 sec

button to conrm.

Use the ”+”

and

”−”

buttons to select the desired power level.

The power levels available are: 2.5kW – 4.0kW – 6.0kW – 7.2kW.

Conrm by pressing

3 sec

The power level selected will stay in the memory even if the power supply

is interrupted.

To change the power level, disconnect the appliance from the mains for at

least 60 seconds, plug it back in, and repeat the above steps.

If an error occurs during the setting sequence, the

”EE” symbol will appear,

and you will hear a beep. If this happens, repeat the operation.

If the error persists, contact the After-Sales Service.

ACOUSTIC SIGNAL ON/OFF

To switch the acoustic signal on/o:

•Connect the hob to the power supply;

•Wait for the switch-on sequence;

•Press the ”P” button of the rst keypad at the top left for 5seconds.

Any alarms set will remain active.

DEMO MODE reheating deactivated, see the section on ”Troubleshooting”)

To switch the demo mode on and o:

•Connect the hob to the power supply;

•Wait for the switch-on sequence;

•Within the rst minute, press the fast heating button ”P” of the bottom

left keypad for 5seconds (as shown below);

•”DE” will show on the display.

ACCESSORIES

POTS AND PANS

Only use pots and pans made from ferromagnetic

material which are suitable for use with induction hobs:

• enamelled steel

• cast iron

• special pots and pans in stainless steel, suitable

for induction cooking

Check for the symbol (usually stamped on the bottom) to determine

whether a pot is suitable. A magnet may be used to check whether pots are

magnetic.

The quality and the structure of the pot base can alter cooking performance.

Some indications for the base’s diameter do not correspond to the actual

diameter of the ferromagnetic surface.

Some pots and pans have only a part of the bottom in a ferromagnetic

material, with parts in another material not suitable for induction cooking.

These areas may heat up at dierent levels or lower temperatures. In certain

cases, where the bottom is made mainly of non-ferromagnetic materials, the

hob might not recognise the pan and therefore not switch on the cooking

zone.

To ensure optimum eciency, always use pots and pans with a at bottom

that distributes the heat evenly. If the bottom is uneven, this will aect

power and heat conduction.

NOOK

Empty pots or pots with a thin base

Do not use empty pots or pans when the hob is on. The hob is equipped with

an internal safety system that constantly monitors the temperature, activating

the “automatic o“ function where high temperatures are detected. When

used with empty pots or pots with thin bases, the temperature may rise very

quickly, and the “automatic o“ function may not be triggered immediately,

damaging the pan or the hob surface. If this occurs, do not touch anything

and wait for all components to cool down.

If any error messages appear, call the service centre.

Minimum diameter of pot/pan base for the dierent cooking areas

To ensure that the hob functions properly, use pots of a suitable minimum

diameter (refer to the table below).

Always use the cooking zone that best corresponds to the minimum

diameter of the bottom of the pot.

Place the pot making sure it is well centered on the cooking zone in use.

It is recommended not to use pots that exceed the perimeter of the cooking

zone in use.

100 mm120 mm

200

mm 150 mm

ø min.

ADAPTER FOR POTS/PANS UNSUITABLE FOR INDUCTION

Using this accessory makes it possible to use pots and pans that are not

suitable for induction hobs. It is important to bear in mind that using it

aects eciency and, consequently, the time needed to heat food. Its

use should be limited because the temperatures reached on its surface

depend signicantly on the pot/pan used, its atness and the type of food

being cooked. Using a pot or pan with a smaller diameter than the adapter

disc may cause heat to build up that is not transmitted to the pot or pan,

which could blacken both the hob and the disc. Adapt the diameter of

your pots/pans and the hob to the diameter of the adapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WL B5860 AL Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WL B5860 AL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info