Bedienungsanleitung Whirlpool WQ9IMO1L (Seite 16 von 40) (Englisch)

756839

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Connect to Water Line

IMPORTANT: If you have turned the refrigerator on before the

water was connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to reduce water pressure in the water line.

3. Use a 3/4-14" shut-off valve or equivalent. The refrigerator is

provided with a household supply line with the installation kit

that connects to the shut-off valve and to the refrigerator.

NOTE: Appliance is equipped with a water installation kit. To

assure proper connection to your water supply, use proper sealing

material in the connection. Check if connection is sealed properly

after some hours of operation.

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.35 mm) O.D. (outside diameter)

soft copper tubing to connect the shut-off valve and the

refrigerator.

■Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, located

on the back of the refrigerator cabinet as shown. Leave a coil

of copper tubing to allow the refrigerator to be pulled out of

the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specic to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Conrm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

4. If ice is desired, turn on the ice maker.

Note: Allow 24 hours to produce the rst batch of ice. Discard

the rst three batches of ice produced. Allow three days to

completely ll the ice storage bin.

A. Sleeve

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WQ9IMO1L Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WQ9IMO1L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info