Bedienungsanleitung Whirlpool wta c (Seite 3 von 4) (Englisch)

302693

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

How to proceed if ...

...you want to correctly

care for and clean your

dryer:

Clean the filter at the end

of every cycle.

• Open the door.

• Pull the filter upwards.

• Open the filter.

• Brush lint using a soft brush or your

fingertips.

• Close the filter.

• Push the filter back into place.

Empty the water container

at the end of each drying

cycle.

• Pull the handle to remove the water

container.

• Empty the water container.

• Replace the water container when empty

by pushing it

completely

back in place.

Clean the heat exchanger

at least every month.

(For further information

see chapter “Heat

Exchanger” in the

Instructions for Use).

• Remove fibres in and around the water

evacuation hole at least once per month.

...you want to check the

dryer yourself first:

(If your machine is not

functioning correctly, please

check the following points

before phoning for the

customer service – also refer

to relevant chapter in the

instructions for use)

Drying takes too long /

laundry is not dry enough.

• Has the correct drying programme been

selected?

• Was the inserted laundry too wet

(washing machine spin speed less than

1000 rpm)?

• Is the lint filter dirty (filter indicator light on)?

• Is the heat exchanger dirty? (for more

information, refer to the instructions for use)

• Is the room temperature too high?

• Are the “End” “ ” and

“Anticrease” “ ” indicator

lamps lighting up? The drying cycle is

complete and the laundry can be taken out.

• If the drying result does not meet your

expectation, select a more dry programme.

The dryer will not operate

(after a power failure,

always press the

“Start (Pauze) / Départ

(Pause)” button).

• Is the plug properly inserted into the

mains electricity socket?

• Is there a power failure?

•Has the fuse blown?

• Is the door properly closed?

• Has a drying programme been selected?

•Has the

“Start (Pauze) / Départ

(Pause)”

button been pressed?

• Has the start delay option been selected?

Lint filter, water container

or heat exchanger indicator

lamps on.

• Is the lint filter clean?

• Is the water container empty?

• Has the water container been inserted

correctly?

• Is the heat exchanger clean?

Water droplets underneath

the dryer.

• Has the heat exchanger been inserted

correctly?

• Has any fluff on the heat exchanger seal

been wiped away?

• Has any fluff on the door seal been

wiped away?

• Has the water container been inserted

correctly?

AFTER-SALES SERVICE

If the fault is still present once the above checks have been undertaken or should the fault occur for a second time, switch the

machine off. Please contact your after-sales service representative (for more information, refer to the warranty manual).

Please have the following details ready when calling your After-Sales service representative:

• The nature of the fault.

• The dryer type and model.

• The service code (the number after the word Service on the

adhesive rating plate) on the right-hand side when the door is open.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool wta c Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool wta c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info