Bedienungsanleitung Whirlpool WUIE2B19 (Seite 7 von 8) (Englisch)

645757

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

TROUBLESHOOTING

Your dishwasher may not work properly.

Before contacting the Service Centre check if the problem can be solved by going through the following list.

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The dishwasher

won’t start or does

not respond to

commands.

The appliance has not been plugged in

properly.

Insert the plug into the socket.

Power outage. The dishwasher starts automatically when the power returns.

The dishwasher door is not closed. Vigorously push the door until you hear the “click”.

It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on

after approximately one minute and reset the program.

The dishwasher

won’t drain.

The wash cycle has not finished yet. Wait until the wash cycle finishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The filter is clogged up with food residues Clean the filter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes excessive

noise.

The dishes are rattling against each. Arrange the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset dish-

washer by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and

run new program without detergent.

The dishes are not

clean.

The crockery has not been arranged

properly.

Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely,

being hindered by the dishes.

Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment

has not been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

MAINTENANCE AND TROUBLESHOOTING GUIDE

For more information, maintenance procedures and troubleshooting,

see the Use and Care Guide.

The Use and Care Guide can be obtained by:

• After-Sales Service; phone number see in warranty booklet.

• download from website: http://docs.whirlpool.eu

• use QR code

TECHNICAL DATASHEET

The technical data containing the energy consumption data can be

downloaded from the website:

http://docs.whirlpool.eu

CONTACTING AFTER-SALES SERVICE

When you contact the After-Sales Service,

you must provide the codes shown on

the rating plate attached to the left or

right side inside the door of the

dishwasher. The phone number is listed

in the warranty booklet or on the website:

http://www.whirlpool.eu

IEC 436

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WUIE2B19 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WUIE2B19

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info