Bedienungsanleitung Whirlpool WVS93F (Seite 1 von 3) (Englisch)

702380

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Quick guide

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT

In order to receive a more complete assistance, please

Before using the appliance carefully read the Safety

Instruction.

PRODUCT DESCRIPTION

FIRST TIME USE

AIR VENT FOR THE SUCTION VERSIONS

Connect the hood and discharge holes on the walls with a diameter

equivalent to the air outlet (connection ange).

Using the tubes and discharge holes on walls with smaller dimensions

will cause a diminution of the suction performance and a drastic

increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensable length.

! Use a duct with as few elbows as possible (maximum elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! The company declines any responsibility whenever these regulations

are not respected.

FILTERING OR DUCTING?

! Your cooker hood is ready to be used in suction version.

To use the hood in ltering version the special ACCESSORY KIT must be

installed.

Check if the ACCESSORY KIT is furnished or must be bought separately.

Note: If furnished, in certain cases, the additional activated carbon ltering

system may be installed on the hood. Information about the conversion of

the hood from suction version to ltering version is present in the Manual

“Safety Instructions & Installation”.

DUCTING VERSION

In this case the fumes are conveyed outside of the building by means

of a special pipe connected with the connection ring located on top of

the hood.

Attention! The exhausting pipe is not supplied and must be purchased

apart. Diameter of the exhausting pipe must be equal to that of the

connection ring.

Attention! If the hood is supplied with active charcoal lter, then it

must be removed.

FILTER VERSION

The aspirated air will be degreased and deodorised before being fed

back into the room.

In order to use the hood in this version, you have to install a system of

additional ltering based on activated charcoal.

CONTROL PANEL

T1. Fan motor OFF / Decrease speed

T2. Fan motor ON / Increase speed

T3. Grease/charcoal lter alarm/reset

T4. 6

sense function (AUTO mode) ON/OFF

T5. Night Light (Ambient light)

T6. Main Light OFF / Decrease intensity

T7. Main light ON / Increase intensity

T1 T2 T3 T4 T5

CAUTION! This hood has an automatic operation system (see below

“T4. 6

sense function (AUTO mode) ON/OFF”). Calibration occurs

automatically each time the hood is reconnected to the electrical

network (e.g.: the rst time it is installed after a blackout). It can also

be performed manually (see paragraph “Sensor set up”). During

calibration, which lasts for 5 minutes, T4 will ash and lights can be

used.

T1. FAN MOTOR OFF / DECREASE SPEED

Press to decrease speed and switch the extraction motor OFF.

Press and hold to directly switch the extraction motor OFF.

T2.

FAN MOTOR ON / INCREASE SPEED

Press to switch the extraction motor ON and increase speed.

press and hold to set 5

speed directly.

Please note: 4

and 5

speed last for 5 mins. then the hood go back to 3

speed.

T3. GREASE/CHARCOAL FILTER ALARM/RESET

At regular intervals, the hood signals the need to perform lter

maintenance.

Please note: The indicators will only work when the hood is on.

T3 lit: Carry out maintenance on the grease lter.

T3 ashing: carry out maintenance of the charcoal lter.

Resetting the lter saturation indicators:

Please note: This must be done with the hood switched on.

Press and hold T3.

The reset of the Grease Filter and Charcoal Filter is performed using the

same key. If both lters alarms are active, the reset procedure will reset

the counter one by one, with priority to the Charcoal.

Activating the carbon lter saturation indicator

Please note: This must be done with the extraction motor switched o.

This indicator is usually deactivated – press and hold T6 and T7

simultaneously to activate the function: Both will light

up to indicate activation.

To deactivate the function, press and hold the same buttons again:

Both will ash briey and then switch o to indicate deactivation.

T4. 6

SENSE FUNCTION AUTO MODE ON/OFF

The hood set the extraction speed automatically if the sensor in the

hood detects changing on ambient conditions.

Please note: to make sure this function is used correctly rst congure

sensor (see “Sensor set up” below).

Please note: if you change any other functions that control the speed, the

“6

sense” function will switch o.

Sensor set up

This can be done when the hood is OFF.

In normal ambient conditions press T4 for 5secs, T4 ashes for 5 mins

to indicate hood is performing sensor calibration, then switches o to

indicate the calibration has ended.

Setting cooktop: Press and hold T1 and T2 simultaneously. Both lit to

indicate hood is ready to accept cooktop parameter calibration.

Press T1 to choose Gas hob (T1 starts to ash for 3 secs to indicate

hood parameters are set for gas hob).

Press T2 to choose Induction hob (T2 starts to ash for 3 secs to

indicate hood parameters are set for induction hob).

* Available only on certain models

Whirlpool WVS93F Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WVS93F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info