Bedienungsanleitung White Knight C96AB-S-W (Seite 8 von 12) (Englisch)

615139

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

REMOVING THE CONDENSER

- Firmly pull the condenser out.

RE-INSTALLING THE CONDENSER

- Carefully push the condenser back into the machine, until it is pushed fully home and a “click” is heard.

IMPORTANT:

- Ensure all lint and fluff is removed from around the seals before closing or water may leak.

- The dryer may leak if the condenser is not correctly re-installed.

CLEANING THE CONDENSER

CAUTION: For maximum efficiency, the plates are made from very thin aluminum and are easily damaged. Do

not try to poke anything between the plates or use a hard object or tool for cleaning. At all times, handle the

condenser carefully and avoid crushing the plates.

–Remove the condenser (see above).

–Flush the fluff from between the plates under running water and carefully shake off excess water.

ANY PROBLEMS

If the clothes are not dry after normal drying time:

- Check that you used the correct heat setting.

- Check that the lint filter has been cleaned. A blocked filter will restrict the airflow.

- Check that the condenser unit and associated duct work are clean. If blocked, these will restrict the

airflow.

- Check that your dryer is heating – the area below the door should feel warm to the touch after the first 10-15

minutes of its programme.

- Check that the bottle full warning light is off. If it is on then the bottle may be full or incorrectly fitted.

Failure to heat may indicate the safety cut-out has operated. To reset, simply press the red button at the rear of the

machine. If it has operated then a sharp “click” will be heard.

This cut-out only operates if the airflow is severely restricted so make sure the filter is clean and that all other

restrictions are removed before re-starting.

If the cut-out continues to operate after checking the above points, you should contact your service agent.

Check that the machine has the correct weight load in the drum before starting the appliance.

If your machine does not work check the following before calling a service engineer:-

- Check that there is a supply of electricity.

- Check that the Activate button has been pressed and that the Display is illuminated.

- Check that the door has been properly closed.

- Check that the water bottle has been withdrawn from, and replaced into the machine. The bottle full warning light

should be off.

- Check the fuse in the moulded plug.

CUSTOMER ADVICE – BEFORE CALLING FOR ASSISTANCE

If the clothes are not dry after normal drying time:

–Check that you used the correct heat setting.

–Check that you have not set the timer within a cool down period.

–Check that the lint filter has been cleaned. A blocked filter will restrict the airflow.

Whilst the condenser is removed, clean as much fluff as

possible from inside the ducting by reaching a hand into the

machine. In particular, keep the passage from the fan clear (on

the right hand side of the condenser duct).

After cleaning, re-install the condenser (see above).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

White Knight C96AB-S-W Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info