Bedienungsanleitung Whynter ARC-101CW (Seite 10 von 18) (Englisch)

727493

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

INSTALLATION

LOCATION

The air conditioner should be placed on a hard and level surface strong enough to support the unit. The unit has

casters and it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpet surfaces. Do not

attempt to roll the unit over objects. Never place any obstacles around the air inlet or outlet and allow at least 20

inch of clearance for efficient air-conditioning.

EXHAUST HOSE INSTALLATION

When using the air conditioner, the hot air from the exhaust hose must be exhausted out of the room to

complete the air exchange of the condenser. When the unit is operating in dehumidifying or fan-only mode,

installation of the exhaust hose is optional.

1. Expand each end of the exhaust hose about 6”

2. Install the hose connectors onto the exhaust hose by turning

clockwise

3. Slide the slide locking hose connector onto the rear of the

unit (Fig. 3)

Only extend the both hoses to the necessary length. We do not recommend extending more than 9' long. If you are

interested in purchasing an additional 5’ exhaust hose, please contact support@whynter.com for retail sales infor-

mation.

WINDOW KIT INSTALLATION

The window kit has been designed to fit most standard vertical and horizontal windows (Fig. 4a and Fig. 4b).

However, it may be necessary to modify the installation procedures to accommodate your window.

NOTE:

• If your window opening is smaller than the minimum length of the window slider kit, the window slider kit can be cut

to fit the window opening. Never cut into the exhaust hose cut-out on the window slider kit.

• If your window opening is larger than the maximum length of the window slider kit, additional material will be

needed to cover the open space such as, Plexiglas, PVC plastic, ply wood, etc. Alternately, an additional window

slider kit can be purchased to be used in combination with the included kit.

• When using the window slider kit on a window or sliding door, additional security measures may be needed.

Fig. 3

Fig. 4a Fig. 4b

Fig. 4c

1. Open the window approximately 5”.

2. Adjust the length of the window slider to the same length and width of the opening of the window. Cut the window

slider if necessary to fit the length of your window.

3. Insert the fixture through the back grooved side of the window slider hose cut-out. Line up the fixture with the 4

screw holes and tighten the fixture with 4 screws from the front side of the slider panel. (Fig. 4c)

4. Fit the window slider kit into the window opening and close the window to secure the window slider kit. For 5.

long term installation, you may screw the window kit into your window frame.

5. Move the unit close to the window, extend the hose to the necessary length, keeping it as short and as straight as

possible and attach the other end of the hose to the window slider kit.

6. Align the tab cut-outs of the hose connector to the tabs on the fixture and snap the hose connector to the window

slider kit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter ARC-101CW Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info