Bedienungsanleitung Whynter ARC-110WD (Seite 13 von 20) (Englisch)

727496

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

13 | P a g e

DEHUMIDIFYING MODE

 In this mode, the air conditioner only dehumidifies the room, the compressor will activate

intermittently depending on the ambient temperature. To activate this function mode, press

the Mode Control button until the indicator comes on. When the dehumidifying mode is

set, the orange light on the front panel comes on.

 Please note that when switching function mode, there will be an approximately 3 minute

transition time. In dehumidifying mode, the exhaust hose does not need to be vented. If the

exhaust hose is vented, the room will be cooled as it dehumidifies. To prevent cooling,

remove the exhaust hose from the window kit and allow the warm air from the rear to be re-

circulated into the room. If room temperature is higher than 77°F, the fan speed can be

adjusted. If room temperature is lower than 77°F, the fan speed is set at Low.

NOTE: When using dehumidifying mode, venting the exhaust hose to the outside is not

required. If vented, the warm air is exhausted to the outside and cooling within the room may

occur. Additionally, if the exhaust hose is not vented, the unit may require more frequent

draining. The air conditioner does not have a humidistat in which a specific humidity level

can be set.

FAN ONLY MODE

 In this mode, only the fan of the air conditioner runs and circulates the air in the room. To

activate this function mode, press the Mode Control button until the indicator comes on.

When the fan only mode is set, the green light on the front panel comes on.

 In this function mode, the temperature cannot be set. Subsequently, set the desired fan

speed by pressing the Fan Speed button. Fan Only mode requires that the exhaust hose be

removed.

NOTE: The unit does not require venting in Fan Only mode.

AUTOMATIC MODE



When you set the air conditioner in AUTOMATIC mode, it will automatically select cooling or

fan only operation between 77 - 85F depending on the ambient temperature. The fan speed

is automatically selected and cannot be changed and the temperature cannot be set.

To activate this function mode, press the Mode Control button until the indicator comes

on. When the automatic mode is set, the light on the front panel displays the color of the

mode that the unit is currently operating in.

NOTE: In Automatic mode, hot air is exhausted from the outdoor exhaust port and the

exhaust hose must be connected to exhaust out the hot air.

FAN SPEED CONTROL

 To set the fan speed, press the fan speed control button. Fan speed can be set at

Automatic, High, Medium and Low.

CLOCK

 To set the clock, press and hold the clock button for 3 seconds. Press the up or down

buttons to set the current time. To save the current time, press and hold the clock button

again for 3 seconds.

TIMER (DELAYED SWITCH ON / OFF) FUNCTION

 This function mode enables a delayed switch ON or delayed switch OFF of the air

conditioner. The time (hours) delay can be set, enabled and disabled. The timer is

adjustable between 1-24 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter ARC-110WD Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info