Bedienungsanleitung Whynter ARC-143MX (Seite 18 von 19) (Englisch)

643513

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

18 | P a g e

The unit has worked for a

long time, but the room is

not cold enough

 Windows or doors are open.

 There are too many people in

the room.

 There is direct sunshine into

the room.

 The room is a kitchen or with

many heat-producing

appliances

 There is a server in the room.

 The room is too large.

 Close all windows and doors.

 You may need additional cooling or another

air conditioner.

 Close curtains or blinds and try to minimize

the amount of direct sunlight into the room.

 You may need additional cooling or another

air conditioner.

 You may need additional cooling or another

air conditioner.

 You may need additional cooling or another

air conditioner.

The unit is very noisy

 The unit is not level.

 The surface underneath the

unit is uneven.

 Low power voltage.

 Make sure the unit is on hard, level and

stable surface.

 Move the unit to a location with a level and

hard floor.

 Make sure the wall outlet and support the

required power consumption of the air

conditioner and do not use an extension cord.

The unit leaks water

 The unit is tilted or not leveled

 The water tank is full.

 Make use the unit is leveled.

 Drain water from the drain plug at the back of

the air conditioner.

The unit needs to be

drained too often

 The humidity in the area may

very high

 Possible loose connection

 Remove the intake hose if the outside

humidity is high or it is raining

 Contact Whynter Service Department

Fan speed cannot be

changed

 Fan speed differences are not

very noticeable

 The fan speed difference is not very

noticeable when the compressor is on. Try

setting the unit to Fan only mode, you should

be able to hear the difference between high

and low fan speed settings.

The unit does not heat

 The room temperature is too

low.

 The heating mode is not on.

 The compressor has not

turned on yet because of its

time delay.

 The set temperature is too low.

 The internal water reservoir is

full.

 The humidity in the area may

very high

 There may be a loose

connection

 The heat pump of the air conditioner does not

operate when temperature is below 45F.

 Press the MODE button until the HEAT light is

show on the display

 Give the compressor 3 minutes to turn on

after the Heating mode has been selected.

 Set the air conditioner to a higher

temperature. It is recommended to set the

temperature to at least 5F of the ambient

temperature.

 Either manually drain the water by removing

the drain plug or allow the unit to exhaust the

water itself by running the fan only mode. The

cooling will resume.

 Remove the intake hose if the outside

humidity is high or it is raining

 Contact Whynter Service Department

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter ARC-143MX Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info