Bedienungsanleitung Whynter RPD-651W (Seite 11 von 15) (Englisch)

727510

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

11 | P a g e

Removing the collected water 1. Pull the bucket out carefully.

There are two ways to remove the collected water.

1. Manual drain

 When the unit is off and the bucket is full, the unit will

beep 8 times and the Bucket Level indicator light will

flash, the digital display will also indicate P2.

 When the unit is on and the bucket is full, the

compressor shuts off but the fan runs for an

additional 30 seconds to dry any moisture on the

condenser. The unit will then beep 8 times and the

Bucket Level indicator light will flash, the digital

display will also indicate P2.

 Slowly pull out the bucket. (Fig 5) Grip the left and

right handles securely, carefully pull the bucket out

to prevent water spillage. (Fig 6) Do not put the

bucket on the floor as the bottom of the bucket is

uneven and it may tip.

 Dispose the water (Fig 7) and reinstall it to the

dehumidifier. The bucket must be installed securely

for the unit to operate.

 The unit will restart when the bucket is restored in its

correct position.

NOTES:

 When the bucket is removed, do not touch any parts

inside of the unit. Doing so may damage the unit.

 Be sure to push the bucket gently all the way into the

unit. Hitting the bucket against anything or failing to

push it in securely may cause the unit to malfunction.

 When the bucket is removed, check if there is any

excess water at the base of the unit. Wipe any visible

water inside the unit before replacing the bucket.

2. Continuous drain

Water can be automatically emptied into a floor

drain by attaching the unit with a water hose( 24mm)

(included).

 Remove the water bucket from the unit and set

aside.

 Lift up the Darin Hose Outlet cover located on the

right side of the unit (Fig.8)

Fig.5

2. Hold both sides of the

bucket evenly and pull it

out from the unit

completely.

3. Pour the water out.

Fig.7

 Insert the female threaded end of the hose to

the Drain Hose Outlet. (Fig.9a)

 Grip the hose from inside the unit and screw the hose

onto the threaded portion of the tray located in the

bucket opening.(Fig.9b)

 Make sure the hose is securely fastened to prevent

leakage. Direct the hose toward a drain or other suitable

drainage outlet. Make sure that there are no distortions

with the hose that may stop the water flow.

 Reinsert the water bucket back in the unit and make

sure that it is inserted securely.(Fig.9c)

 Select the desired humidity setting and fan speed on

the unit for continuous draining to start.

NOTE: If the unit stops operating, check if the Bucket

Level light is illuminated. If it is, remove the bucket and

empty the water and then check the seal between the hose

and the drip tray. If there is a leak, replace the hose gasket

and re-tighten the hose.

Fig.9b

Fig.9a

Fig.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter RPD-651W Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info