Bedienungsanleitung Whynter RPD-951DXP (Seite 13 von 18) (Englisch)

727522

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

WATER DRAINAGE INSTRUCTIONS

2. CONTINUOUS / GRAVITY DRAIN METHOD

Water can be automatically emptied into a floor drain by attaching the 20” continuous/gravity drain hose to the con-

tinuous/gravity drain outlet. To use gravity to drain your portable dehumidifier, it must be installed on a level surface

or at least 12 inches above the ground, on a sturdy table or shelf unit. When using the function of continuous/

gravity drainage, your drain hose must be placed horizontally below the drainage hole. Avoid uneven ground and

folding the hose.

NOTE: When using continuous/gravity drainage setup, there may be some water collected in the water in the drain

bucket

1. Remove the continuous drain cover and then attach the 20” con-

tinuous/gravity drain hose. Make sure the hose is securely fastened

to prevent leakage.

2. Direct the drain hose toward a drain or other suitable drainage

outlet. Make sure that there are no distortions with the hose that may

stop the water flow. (See Fig. 7)

3. Select the desired humidity setting and fan speed on the unit for

continuous draining to start.

3. WATER PUMP METHOD

One of the key features of this dehumidifier is that it has a water pump that pushes water up or over a longer dis-

tance. Using this feature will enable your unit to run maintenance free.

NOTE: The water pump will ONLY engage when the drain bucket is full.

NOTE: The Pump Indicator Light will flash when there is a failure in the

pump operation. Please turn off the unit and unplug the power cord and

check the following points:

• Clean the pump filter - remove the drain bucket from the unit, pull down

the pump filter, and clean (See Fig. 9)

• Check the pump drain hose for kinks or obstructions

• Reinstall the pump filter and drain bucket properly. Turn on the unit. If

the error repeats, call for service

• Do not use this operation when the outdoor temperature is equal to or

less than 32°F. Otherwise, water hose may be blocked as the water will

turn to ice and cause the unit to fail. When the pump drain feature is not

being used, remove the pump drain hose from the outlet.

1. Make sure the continuous/gravity drain assembly is removed from

the continuous/gravity drain outlet and the plastic cover is installed.

2. Insert the 16 ft. pump drain hose (included) into the bottom pump

drain outlet (See Fig. 8), then lead the drain hose to a suitable drain-

age facility. Make sure that the hose is fully inserted to avoid water

leakage and no kinks which will cause the water to stop flowing.

3. Press the Pump button to activate the pump operation.

NOTE: The water pump will ONLY engage when the drain bucket is

full.

4. The water pump may make some noise when it starts to work with-

in the first 3 - 5 minutes. This is a part of the unit’s normal operation.

5. Select the desired humidity setting and fan speed on the unit.

Fig. 7

Fig. 8

Pump Drain

Outlet

Pump Drain

Hose

Fig. 9

Pump filter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whynter RPD-951DXP Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info