Bedienungsanleitung Wiking Olympic (Seite 29 von 56) (Englisch)

745749

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

Lighting and Firing Your WIKING Wood-Burning Stove

The rst ring

The rst time you re your wood-burning stove, you must do so carefully, as all materials need to

adjust to the heat. This means that the stove must be heated slowly, until it reaches its maximum heat

level. Afterwards, you should re a few times so that the stove is thoroughly heated throughout.

Be careful of the lacquer

The lacquer used to treat the wood-burning stove will harden the rst 2-3 times the stove is

red, and this can create unpleasant smoke and odours. Ensure therefore that the room is well

ventilated. The door must also be carefully opened; otherwise there is a risk that the seals will

stick to the lacquer.

Warning: The enclosed gloves can scratch the surface paint if the lacquer has not hardened

properly. Be careful not to touch the lacquered surfaces until after the rst 2-3 rings.

Lighting

1. Both the primary and secondary dampers beneath the door are pushed as far to the left as

possible. This completely opens up both primary and secondary air.

2. Stack 8-10 nely split pieces of rewood, corresponding to 1-2 kg, inside the wood-burning stove.

The smaller the sticks, the shorter the time needed for the stove to be heated and for the optimal

combustion temperature to be achieved.

3. Place two relighters between the top layer of kindling. WIKING recommends using high-quality

relighters, as they do not produce smoke or odours.

4. Light the relighters. Keep the door ajar for a couple of minutes until the glass is hot - this

prevents condensation. Then close the door completely.

5. When the rewood is burning well, push the primary damper all the way to the right while slightly

adjusting the secondary damper to get an even and steady combustion.

Warning: The door may only be kept open when lighting, adding rewood or cleaning the

wood-burning stove; otherwise combustion becomes too powerful, which in turn increases the

risk of the stove becoming overheated.

Firing (adding rewood)

When there are no more visible ames and only a solid layer of embers remains, more fuel

can be added to the re.

1. Carefully open the door to prevent smoke and embers from escaping.

2. Lay 2-4 pieces of split rewood (approximately 2 kg) on top of the embers.

3. Close the door and completely open the primary and secondary dampers by pushing them to the left.

4. After a short while the ames should are up again. When the rewood is fully ignited, push the

primary damper to the right again while slightly adjusting the secondary damper, until the ames

burn evenly and steadily.

Warning: During combustion, the stove’s surfaces and door become extremely hot

- exercise great caution.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wiking Olympic Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wiking Olympic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info