Bedienungsanleitung Wiking Volcanic 2 (Seite 21 von 52) (Deutsch, Englisch, Italienisch)

745741

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installation Instructions

Before You Start

Figure 1 is a cross-sectional view of your wood-burning stove. Here you

can gain an overview of the parts of which your stove consists.

1. Steel smoke deector.

2. Vermiculite smoke deector.

3. Vermiculite rear plate.

4. Vermiculite base plates.

5. Grate.

6. Vermiculite front piece.

7. Heat shield.

8. Air-regulation damper.

Please note: The combustion chamber is covered with plates made of

vermiculite, which is a heat-insulating material. These plates ensure

that the optimal combustion temperature is quickly reached, and they

must therefore remain inside in the wood-burning stove.

The steel smoke deector and the vermiculite smoke deector ensure that the passage of

smoke through the stove is as long as possible, so that the ue gasses have more time to emit

their warmth within the stove and the surrounding area. In this way you get more warmth from

the wood you add to the stove, as the warm smoke is not simply sent out through the chimney.

Arrangement of Individual Components

It is important to ensure that all individual components are in place and no damage was done

to them during transport. In Figure 1 you can see the parts that you must inspect:

The steel bafe plate is hung from two hooks and equipped with two pins that serve as

protection during transportation. Remember to remove the two pins before you start using

the stove. Lift the skamol bafe plate off the combustion chamber and pull the two pins free

from the hooks.

2. The vermiculite smoke deector should rest on the side plates and be pushed all the way

back in the combustion chamber.

3. The rear plate must be pushed all the way back in the combustion chamber.

4. The base plates must lie at on bottom around the grate.

Only when you are condent that the individual components are in place, you may begin with

the installation of the wood-burning stove.

Changing the Smoke Outlet from Top Outlet to Rear Outlet

Proceed as follows to change the smoke outlet from top outlet to rear outlet:

1. Lift the top plate off the stove.

2. Remove the smoke ring on the top of the stove by unscrewing the three screws and lifting it off.

3. There is a cut-out for the ue duct in the back plate. Break off the plate within this cut-out to

make a hole that the ue duct can t into.

4. Remove the cover plate on the back of the stove by unscrewing the three screws (Torx Bit

no. 30) and lifting it off.

5. Install the cover plate on top of the stove with the three screws.

6. Place the smoke ring in the smoke outlet hole in the back of the stove and secure it with the

three screws.

7. Replace the top plate on the stove.

Fig. 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wiking Volcanic 2 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wiking Volcanic 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info