Bedienungsanleitung WLtoys Q282G spaceship (Seite 7 von 8) (Englisch)

608990

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Steps to install the FPV set on your copter:

1. screw the antenna (1) on the FPV monitor (2)

2. Install the sun block cover (3) on the FPV monitor for better

visibility during sharp sunlight.

3. Mount the FPV monitor (2) on remote (5) by using the FPV

mount bracket (4) and screw set.

4. Turn the monitor on on the right side and then the camera

which is mounted to the copter. Make sure the Antenna of the

camera is extended and connect the camera to the FPV socket

of the copter.

Troubleshooting

1. The receiver LED blinks continuously for more than 4 seconds after the quadcopter battery have been inserted. No response to

the command input. The transmitter is not connected to the device. Repeat the power-on initialization process.

2. No response from the quadcopter after the battery have been connected. There is probably contact failure on the battery

terminals. Turn on the transmitter and ensure that the battery of the vehicle is correctly inserted. Replace the battery and ensure

good contact at the battery's connections. Use fully charged batteries in the remote.

3. The motor does not respond to the throttle stick and the receiver flashes. The quadcopter's battery is exhausted. Charge the

battery or replace it with a charged battery.

4. The main rotor continues to rotate after landing. Confirm that the gear lever is oriented downward.

5. The main rotor rotates but the device does not take off. The blades may be distorted or the quadcopter battery is exhausted.

Charge or replace with a fully charged battery and / or replace the blades.

6. The quadcopter suffers of strong vibrations. The blades are distorted. Replace the blades.

7. The tail is not balanced after adjusting the clip or speed is inconsistent in the left / right pirouette. Tail rotors are probably

damaged. Replace the main wing and / or the main engine.

8. The quadcopter was still moving forward after the adjustment of the levers during hover. The gyroscope is not correctly

calibrated. The gear lever is placed too high or too low. The boot refines the calibration therefore restart on a flat surface.

9. You can not fly, the helicopter falls. The motor is probably fall out or the gears are loose. Reinstall the motor and tighten the

gears.

Spare parts

FPV

Wltoys

The copter is not sensitive to crashes, but in case of extreme drops it is possible that some parts may break. All parts can be

ordered and easily assembled. Please contact your dealer or visit www.wltoys.eu for more information.

If the copter is unstable, resulting in frenetic flying in all directions, and rotates around its axis so that you have to constantly

correct its flight, then the gyroscope is probably not calibrated properly. To perform recalibration, connect the drone to the

transmitter (part Activation in the manual), then click on 100% button of the remote and move both sticks to the bottom left. When

the calibration is performed, you will either hear a long beep or see flashing lights (on the PCB) or both.

Note: The calibration is done in the factory, it is usually not necessary to do it when you receive the product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WLtoys Q282G spaceship Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von WLtoys Q282G spaceship

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info