Bedienungsanleitung Wmf Aroma Thermo to go (Seite 16 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

712210

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Notes on the Cromargan® thermal jug and thermal beaker

The thermal jug and thermal beaker best keep contents warm when ﬁlled to the maximum level. The

time the content is kept warm may be reduced signiﬁcantly if the jug/beaker is only partially ﬁlled or

almost empty.

Note: It is best to rinse the thermal jug/beaker with hot water before use. To seal, turn the lid in a

clockwise direction until it sits snugly on the thermal jug/beaker. To pour, press the pour button on the

lid. To open the thermal jug/beaker, turn the lid slightly counter-clockwise. The thermal jug and ther-

mal beaker are made of double-walled Cromargan® and therefore completely shatter-proof. However,

they should be protected against mechanical stresses nevertheless. Rinse out the thermal jug/beaker

regularly. If iron particles from water accumulate on the Cromargan® surface, they can cause pitting

at those points. These deposits must therefore be removed immediately with a stainless steel cleanser.

Cleaning and care

Cleaning

Unplug the mains plug and allow the appliance to cool down.

Do not immerse the appliance in water. Outer surfaces can be cleaned using a damp cloth and a little

washing-up liquid.

Do not use harsh or abrasive cleaning agents.

The ﬁlter (3), thermal jug (8) and thermal beaker (9) can be cleaned under running water. Alternatively,

you can also clean them in the dishwasher.

Scale indicator

Limescale deposits extend brewing times and lower the quality of your coffee. They also lead to energy

losses and impair the service life of the appliance. The automatic scale indicator determines when

it is time for descaling. Depending on coffee consumption and the set water hardness, you may be

prompted to descale every 4-6 weeks. This is indicated when the descaling symbol (

) is displayed

permanently.

Setting the water hardness

Your appliance has an automatic scale indicator. To prevent too much limescale building up, the appli-

ance is set for very hard water by default. Ask the responsible waterworks or local authorities about

the hardness of your tap water. Change the default setting if the water hardness is less than 21°dH.

You will then not be prompted to descale as often as before. To this end, press and hold the descaling

button (the - button) for about 3 seconds until the display (6) shows the currently set water hardness

(H1, H2, H3 or H4) and the descaling symbol (

). Press the + or - button to adjust the water hardness.

Conﬁrm the setting by pressing the timer button (

Hardness range Hardness

1 Soft 0-7° dH

2 Medium >7-14° dH

3 Hard >14-21° dH

4 Very hard >21° dH

1° dH corresponds to about 0.18 mmol/l Ca and Mg ions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wmf Aroma Thermo to go Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info