Bedienungsanleitung Wmf WMF 3 (Seite 6 von 11) (Deutsch, Englisch, Französisch)

484837

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

10 11

DEGBFR

Cleaning and service

Pull out the power plug prior to cleaning. Never immerse the

kettle and the base in water. Brieﬂy rinse the kettle from time

to time. Wipe the outside of the appliance only with a damp

cloth. Do not use harsh or abrasive cleaning agents.

The mesh ﬁlter in the spout can be removed for cleaning

when the lid is open. To do so, press the top lug downwards.

To reinsert the mesh ﬁlter, position the mesh ﬁlter in the middle

of the spout and then push forward to lock into place. The he-

ater bottom is made of stainless steel. If you notice rust marks

nevertheless, these are only deposits sticking to the surface.

Remove them immediately with a cleaning agent for stainless

steel.

Decalcifying

Calcium deposits result in energy losses and impair the service

life of the appliance. The appliance will switch off prematurely

if the calcium deposits are too strong. It is then very difﬁcult to

remove the deposits. Decalcify the appliance regularly.

Therefore, the pot should be regularly descaled with usual

descaling agents suitable for stainless steel. Please consider the

user instructions of the manufacturer. Pour out the water and

rinse the kettle thoroughly with cold tap water. Do not heat up

the kettle during the decalciﬁcation process.

Important. Warranty compensation does not exist for damage

that occurs due to non-compliance with the decalciﬁcation

instructions.

Causes of faults

· The appliance switches off before boiling

There are excessive calcium deposits on the bottom

of the kettle, or

· The appliance does not switch off

Close the cover until it locks into place.

The mesh ﬁlter is not correctly ﬁtted.

· The kettle does not pour properly

Decalcify the mesh ﬁlter.

· The appliance cannot be switched on

The kettle has not cooled down sufﬁciently after

being operated with no or too little water.

If the fault cannot be remedied, you must return the appliance

for repair.

For UK use only

· This product is supplied with a 13 A plug conforming to BS

1363 ﬁtted to the mains lead. If the plug is unsuitable for

your socket outlets or needs to be replaced, please note the

following. If the plug is a non-rewireable one, cut it from

Start-up

Prior to using for the ﬁrst time, clean the inside of the kettle

thoroughly. To do so, pull the lid lock to open the lid. A mesh

ﬁlter is ﬁtted in the spout to hold back large pieces of calcium

deposits when pouring out the water.

The section of the power cable not in use, can be wound

up and stored on the base. Connect the power plug to a

shockproof socket.

Fill in at least as much water that it can be seen in the window,

but not further than the max. mark. Close the lid and make sure

it locks into place. Otherwise the automatic boil-stop function

cannot function properly.

Place the kettle onto the base pointing in any direction. Only

then press down the ON switch under the handle. The indica-

tor light on the ON switch will indicate that the appliance is

heating up.

The ON switch will only lock into place if the kettle is positioned

on the base.

Due to the high level of power consumption during the boiling

process, you will notice an increase in noise.

Do not use the water from the initial boiling operation for food

purposes.

Automatic switch-off

A short time after the water has started to boil, the automatic

boil-stop function will switch off the appliance. If the kettle is

ﬁlled with only a small quantity of water, the switch-off time

will increase.

If you require only warm water, the heating process can be

cancelled at any time by pressing the ON switch. The appliance

will switch off automatically after the kettle is removed from

the base. If you want to reboil hot water, the appliance can be

switched on again.

For functional reasons, some condensed water may run from

the openings at the bottom of the kettle onto the rim of the

base. This is necessary for technical reasons and does not impair

the safety of the appliance.

Safety system

If the kettle is accidentally operated without water, a thermo-

stat will protect the kettle from overheating by switching off

the appliance.

Before ﬁlling in water, leave the kettle to cool down for 5-10

minutes.

If the ﬁrst thermostat fails due to incorrect use, an additional

temperature limiter offers reliable protection.

BAL_waterkettle_BrandLoyalty_148x210_RZ.indd 10-11 20.04.11 16:04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wmf WMF 3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info