Bedienungsanleitung Wodtke Crazy.nrg (Seite 6 von 68) (Englisch)

813056

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Manual_S5_Airplus_2015_04_20 Page 6 / 68

3.2 Installation Room

Wodtke Pellet Primärofen furnaces may only be

installed in residential spaces with ordinary im-

purities, normal relative humidity (dry rooms ac-

cording to VDE 0100) and with room tempera-

tures from +5 °C to +30 °C (environmental tem-

peratures during operation).

The furnaces are not splash-water protected and

may not be installed in wet rooms. Due to the op-

erating and flame noises of the furnaces, we do

not recommend installation in bedrooms or relax-

ation rooms. Operating sounds, such as pellets

dropping and flame/air current and drive motor

noises, are audible during operation. In tempera-

tures of <5 °C (e.g. in summer cottages), certain

minimum settings must be made on the furnace

and appropriate frost protection devices (e.g. elec-

trical heat monitors) must be provided for. Safety

equipment can be effective in operation at temper-

atures >30 °C. Please observe the respective no-

tices on heating operation in the unit's instructions.

The installation room or combustion air connection

for all furnaces must have at least 4 m³ of volume

per kW nominal heating output: 6 kW  24 m³.

Please observe the specifications on fire protec-

tion regulations. The furnaces must be installed on

a sufficiently load-bearing and non-flammable

base. At least 20 cm of free space must be avail-

able to the rear and sides of the furnaces after in-

stallation for assembly work. Please also note that

the units should be equipped by the customer with

flexible connections (electrical lines) so that they

can be subsequently moved for possible assembly

work / repairs and are easily accessible.

3.3 Connection of External Con-

trollers

All units can be conveniently and easily activated

and deactivated by hand. In addition, wodtke of-

fers compatible room and clock thermostats for

automatic activation of the units (see price list).

Solid fuels, such as wood pellets, require more

time for ignition than liquid or gaseous fuels.

The ignition process leading to the first flame al-

ready requires several minutes and the furnace's

full output is not available until about 15

minutes after starting, when the warm-up pro-

gramme is complete.

When the furnace is shut off, it also takes sev-

eral minutes - in contrast to oil or gas furnaces

- until all pellets have been burned and the

flame goes out. Consequently, a fan stop delay

of several minutes is programmed into the fur-

nace, which should elapse before the furnace is

restarted.

Due to the required warm-up programme and

the fan stop delay, there is therefore less out-

put available during frequently cycling opera-

tion in comparison to oil or gas furnaces.

In the case of automatic activation of the units with

other controllers, a minimum unit run time of

30, preferably 60 minutes should be observed.

This means that the controller must be configured

so that too-frequent cycling (on-off) of the unit

is prevented. The hysteresis of the external

controller should be selected to be large enough

that at least 15 minutes pass for the fan stop delay

between the "shut-off" and "restart" signals.

For installation of the required electrical connec-

tion lines, we recommend two empty conduits with

at least Ø 30 mm be provided by the customer

(separated into empty conduit for 230V and 24V

connection lines).

3.4 Important Notices Regarding

Room Air Dependent and

Room Air Independent Oper-

ation

3.4.1 General Notices

Please always observe the respective local regu-

lations and rules, in consultation with your author-

ised district chimney sweep. We can accept no li-

ability for changes which occur after printing of

these instructions. We reserve the right to make

changes without notice.

3.4.2 Room Air Dependent Operation

The furnace is standard-delivered as a room air

dependent pellet furnace. That is, the furnace ex-

tracts all of the combustion air from the installation

room via the central air intake on the rear side of

the furnace. A sufficient combustion air supply is

mandatory (approx. 25 m³/h at full output).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Crazy.nrg Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Crazy.nrg

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info