Bedienungsanleitung Wodtke Crazy.nrg (Seite 54 von 68) (Englisch)

813056

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Manual_S5_Airplus_2015_04_20 Page 54 / 68

Fault code

Class 1

Cause of fault

Target values

Resolution of fault

TR =

Flue gas temperature

too low. Measurement point:

Combustion chamber.

Sensor NiCrNi

Image / case 1

Do not ignite! Empty pot

first. See to the right

Flue gas fan temperature TR

too low. There are often also unburned

pellets in the burner pot.

Case 1: False start; burner pot filled

with pellets, no flame. TR temperature

not reached:

 Burner pot / unit not cleaned 

false start

 Negative pressure in installa-

tion room (resulting in flow re-

versal in the ignition)  false

start (often associated with flue

gas escaping from the unit)

 Ignition cartridge defective 

false start

TR ≥ 150 °C

Query occurs 18

minutes after the

start signal for

the furnace for

the first time, and

is then monitored

continually.

Upon restart, the

query waits 18

minutes again.

Always clean / empty burner

pot before restarting. Atten-

tion: Never empty content of

burner pot into the storage

container – risk of fire from

embers!

Troubleshooting: Inspect,

verify combustion air supply.

Negative pressure in the in-

stallation room of the furnace

due to exhaust hood, residen-

tial ventilation or pneumatic

conveyance systems is not

permitted and dangerous.

Also see country-specific reg-

ulations and separate tech-

nical information. Inspect igni-

tion cartridge. Only after-

wards, perform manual reset

via I/O button

Image / case 2

Do not ignite! Empty pot

first. See to the right

Case 2 cause: Shut-down in opera-

tion, because there aren't enough pel-

lets in the storage container or container

has run empty (there are only a few pel-

lets in the burner pot)

Remedy for case 2: refill pel-

lets, empty / clean burner pot.

Reset and restart.

TP =

Pellet chute temperature too

high

Measurement point: Pellet

chute

Measurement sensor: TP 1000

External error!

Caused for example by negative pres-

sure due to ventilation system or extrac-

tion hood. Or chimney draught much too

low with voltage failure (fan). Or pellets

with through-put/heating value that is

much too high.

TP < 200 °C

There is not a unit defect!

Allow unit to cool until TP is

below threshold.

Find and resolve exter-

nal cause. Only afterwards,

manual reset via I/O button

See above regarding nega-

tive pressure

ST =

safety temperature limiter STB

has triggered!

Measurement point of air units:

capillary sensor on storage

container radiation plate

STB measurement sensor ac-

cording to DIN 3440. Notice,

the STB is a mandatory, au-

tonomous safety component

with its own switch housing

and operates decoupled

from the control.

External error!

Unit temperature is too high. STB trig-

gered because temperature is too high

(safety function). Normally an external

cause, not a unit fault, because STB is

only triggered if the heat generated by

the unit is not withdrawn.

Causes: Overheating

T STB ≤ 95 °C

no query possi-

ble.

There is not a unit defect.

Find and resolve external

cause. Inspect convection

air inlets and outlets. Re-

duce heating output if the

room temperature is too

high.

Allow unit to cool until STB

is below threshold. Only af-

terwards, unlock the STB+

manual reset via I/O button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Crazy.nrg Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Crazy.nrg

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info