Bedienungsanleitung Wodtke CW 21 Waterplus S4 (Seite 68 von 83) (Deutsch)

813071

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 68 / 83

9.11 Inspecting the suction pipe and air flow sensor (all models)

Important note: If the stove is connected to an external combustion air pipe, you should

first inspect this pipe along its entire length for any blockage before inspecting the

suction pipe and air flow sensor. This is to establish whether the suction pipe and air flow

sensor are at all times supplied with a sufficient flow of combustion air. The combustion air pipe

must be completely cleared of any foreign matter or deposits (such as lumps of dust).

Combustion air pipes should always be arranged such that their opening outside the building is

protected against wind pressure.

Having checked the combustion air pipe inspect the suction pipe and air flow sensor that

are located directly next to the appliance. Use a mirror and torch to look inside the

suction pipe. There are 2 things to look out for.

1) Check air flow sensor (LMS) for dust / fluff

The sensor and suction pipe must be free of dust and fluff. If this is the case, you need to clean

neither the air flow sensor nor the suction pipe. Only dismount the air flow sensor and clean

it together with the suction pipe if you find dust deposits or bunches of hair or the like (see next

chapter for dismounting instructions).

2) 2) Check air flow sensor (LMS) for soot or blackening

If the sensor shows no signs of soot, it should be in order. There is no need to clean the air

flow sensor and the suction pipe. Only if the sensor shows soot or even signs of blackening

should it be dismounted and cleaned gently using a paint brush and soft cloth. These are signs

of external trouble and/or insufficient cleaning with resultant flow reversal in the suction

pipe. It is essential to find and rectify the cause of the external disorder (see also Chapter

0). It is also advisable to carry out a brief functional check* to determine whether the air flow

sensor is still working properly.

*Brief functional check of the air flow sensor: Open door while stove is in operation. The stove should shut down

within approx. 20 s, with the display showing “LO L-“, and then start up again when the door is closed. Alternatively,

you can have a service technician do a complete functional check, i.e. check the resistors of the air flow sensor

and replace the sensor if necessary.

Note:

Never clean the air flow sensor when mounted and don’t clean it with a brush or the like.

This could destroy the sensor electronics. Observe the instructions in the following

chapter.

air flow sensor (LMS)

Inspect air flow

sensor with a

torch.

mirror

suction pipe

Direction of flow

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke CW 21 Waterplus S4 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke CW 21 Waterplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info