Bedienungsanleitung Wodtke Easy.nrg S5 (Seite 31 von 68) (Englisch)

813148

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Manual_S5_Airplus_2015_04_20 Page 31 / 68

The rear wall of the furnace does not become hot.

No minimum distance must be maintained for fire

safety reasons. Nevertheless, we strongly recom-

mend maintaining a distance of 20 cm to the rear

(e.g. for maintenance work) in order to ensure ac-

cessibility.

Floors made of flammable material, such as car-

pet, parquet flooring or cork, must be replaced or

protected by a surface of non-flammable materi-

als, such as ceramic, stone, glass or a floor plate

made of steel, under the furnace as well as in front

of the combustion chamber opening at least 50 cm

to the front and at least 30 cm to the sides beyond

the furnace opening (not the outside edge of the

unit, but rather the inside edge of the combustion

chamber opening).

No additional thermal insulation is required

underneath the furnace; a load-bearing and

fire-safe surface is sufficient, as there is no

downward heat emission. All air intake and outlet

openings must be kept completely free and may

not be blocked or covered: danger of the furnace

overheating!

The minimum clearance between the hot flue

pipe (connection piece to the chimney) and

components to be protected must be designed

according to the the specifications of the

manufacturer of the flue pipe (Dimension D).

If the flue pipe is not connected directly

horizontally as recommended, but rather led

vertically behind the furnace, the vertical part of

the flue pipe must have a minimum clearance of

5 cm to the rear wall of the furnace (dimension

E) .

If the flue pipe is run through a wall with flammable

components to the chimney, either a non-

flammable, dimensionally stable thermal

insulation is required in a perimeter of 20 cm to

the flue pipe, or a protective tube at a distance of

20 cm to the flue pipe is required (Maß F).

11 Approved Fuels

According to the 1st Federal Immission Control

Act (1st BImSchV), only natural wood pellets are

permitted. Cut firewood or other burnable or waste

materials may never be used.

Only pellets which have been certified accord-

ing to ENplus-A1, DINplus or DIN EN 14961-2

Class A1 may be used in wodtke Pellet-

Primärofen units. Wood pellets with an ash

content of > 0.7% may also not be used, as oth-

erwise the cleaning and maintenance expense

is too high. Be sure to observe the notices re-

garding pellet quality in Chapter 3.8!

Cut firewood or other burnable or waste mate-

rials may never be used. Other fuels also lead

to damage to the wodtke Pellet Primärofen and

burden our environment.

If the furnace is not operated with approved

fuels, any warranty or guarantee claims are

void and dangerous operating conditions may

result. Do not perform any experiments.

A pellet diameter between 5 and 8 mm is per-

mitted

. The length of the pellets should not ex-

ceed 30 mm. Pellets with high dust content (>5%)

should likewise not be used.

The recommended pellet diameter is 6 mm; in case of devia-

tions, the fuel throughput may need to be adjusted. The same also

applies for differing lengths.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Easy.nrg S5 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Easy.nrg S5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info