Bedienungsanleitung Wodtke Easy.nrg S5 (Seite 36 von 68) (Englisch)

813148

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Manual_S5_Airplus_2015_04_20 Page 36 / 68

Note: Depending on which programme is set on

the furnace, the following output ranges can be

set:

Programme P5: heating output H = 2.0 - 6.0 kW

The following indicators can appear on the display

during operation of the furnace:

Display

indicator

Meaning

Stand-By-Dot Furnace has been manually de-

activated via the I/O button. The I/0 button

must be pressed to activate the furnace. In

stand-by mode, the furnace is not operation-

ally ready for external controllers.

ON start signal (displayed briefly upon activat-

ing the furnace)

The furnace was started and enters the

warm-up programme shortly after displaying

the programme and an internal test.

OFF

OFF stop signal (displayed briefly upon deac-

tivating the furnace)

The furnace was deactivated and enters the

fan stop delay G OFF.

400

Indicates the programme and the programme

version (displayed for several seconds upon

starting)

P5 = Programme 2-6 kW

400 = Programme version 400, 401 = Pro-

gramme version 401 etc.

-15

WARM-UP PROGRAMME + indication of re-

maining duration in minutes

The furnace begins to throw in pellets, the ig-

niter element is started, the ignition is moni-

tored (after correctly warming up, the furnace

switches to the heating programme H). The

warm-up programme takes 15 minutes. The

display counts down by minutes.

-15

WARM-UP PROGRAMME IN + display in

minutes

(blinks in alternation with G OFF). The fur-

nace is still in G OFF.

However, the furnace has registered that the

I/O button was pressed again. The furnace in-

dicates that it will automatically resume oper-

ation in x minutes (after G OFF elapses).

AI 11 = warm-up in 11 minutes.

...

HEATING PROGRAMME + display of ad-

justed output in kW

The furnace is in heating mode. H 6.0 = heat-

ing programme 6 kW.

R.M

2.0

Internal modulation on flue gas side + display

of output in kW

 The flue gas temperature "TR" was

exceeded. The furnace is run at the

lowest output (2 kW) via the internal

control. Once the temperature low-

ers sufficiently, the furnace returns to

the heating programme H.

 The temperature on the air volume

sensor was exceeded. The furnace

regulates to the lowest output (2 kW)

Once the temperature lowers suffi-

ciently, the furnace returns to the

heating programme H.

120

CLEANING PROGRAMME R + indication of

remaining duration in seconds

An automatic cleaning cycle of 120 seconds

is started after each hour of continuous oper-

ation in heating programme H. Pellet convey-

ance is reduced and the fan speed is in-

creased in order to reduce the pellet volume

in the burner pot and to centrifuge the flue

ash out of the burner pot.

OFF

FAN STOP DELAY (= furnace shut-down.

Duration 15 minutes)

The furnace shuts down. The fan runs for 15

more minutes in order to fully burn away the

remaining pellets and to remove the heating

gases. Attention: the furnace only actually

goes into Stand-By after G OFF when G OFF

does not blink in alternation with HE OFF or

TW OFF. In other cases, the furnace can /

will be automatically restarted after G OFF.

...

Maintenance indicator (displayed briefly)

The furnace must be serviced. Display WA

0.1 = maintenance 0.1 d overdue

Display "Function not available"

This display appears if the desired button

function cannot be performed or has no func-

tion assigned.

...

HEATING PROGRAMME EXTERNAL (only

possible with externally modulating controller)

The furnace is adjusted to the displayed out-

put via an external modulating controller.

e.g. HE 5.2 = heating programme external 5.2

2.0

HEATING PROGRAMME MINIMUM (only

possible with external controller)

The furnace is adjusted to lowest output (2

kW) via an external controller (via the

MIN/MAX input).

OFF

HEATING PROGRAMME EXTERNAL (only

possible with external controller)

The furnace is shut down via an external con-

troller (via the ON/OFF input or BUS)

…

Processing remaining time: the furnace was

shut down via an external controller (via the

ON/OFF input). The remaining time is dis-

played as a countdown in minutes, in alterna-

tion with the current operating state. This

function is only possible if the remaining time

was set to >0 (menu level 2).

OPEN

Pellet drawer open.

The pivoting lid of the pellet container is

open. If it is opened for longer than 3 minutes

without interruption during furnace operation

(mode = A, H, HM, R.M, HE, G OFF), the fur-

nace goes into fault (PL, Err).

OPEN

Combustion chamber door open.

The combustion chamber door is open. If the

combustion chamber door is opened for

longer than 1 minute without interruption dur-

ing furnace operation (mode = A, H, HM,

R.M, HE, G OFF), the furnace goes into fault

(FT, Err).

Only open combustion chamber door when

the furnace is not operating!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Easy.nrg S5 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Easy.nrg S5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info