Bedienungsanleitung Wodtke Frank SX waterplus S4 (Seite 6 von 83) (Deutsch)

813089

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 6 / 83

As a practical guide value, the largest of our Waterplus appliances (10 kW nominal heating

capacity) is capable of generating a maximum 15,000 kWh per year. This is equivalent to 1500

full load operating hours without interruption at a thermal output of 10 kW. Note that when

delivered by an appliance of our “Topline” series, 40% (= 6,000 kWh) of this thermal output

would go towards heating the room of installation, while with an appliance of our series “Smart”

“PE” or “CW 21” the share of heat delivered to the room of installation would be around 20%,

i.e. 3,000 kWh. This must be taken into account in the planning phase by ensuring that

the room of installation is sufficiently large. The following section contains recommendations

for minimum room sizes and suggestions for alternative solutions for smaller rooms of

installation.

2.2 Minimum room sizes

For all wodtke pellet stoves, the room of installation should at minimum have a floor area of 10

m² and a room volume of 15 m³. With Waterplus appliances one must also take into account

that the room of installation is additionally heated through heat radiation and convection. The

following guide values apply in this case:

• Topline Waterplus appliances (60% of thermal output delivered to water*):

room of installation should account for at least 50% of total heated floor area

• Smart / PE / CW 21 Waterplus appliances (80% of thermal output delivered to water*):

room of installation should account for at least 30% of total heated floor area

If the room of installation is too small or the hot water demand to high, the room of installation

will become overheated.

Heating surfaces in the room of installation of a Waterplus appliance: If solar energy

plants or buffer storages are used for auxiliary heating, then the room of installation of the

Waterplus appliance must have additional heating surfaces (radiator, floor heating) so that it can

be heated even when operation of the boiler is not required. This can be the case in

interseasonal periods, for example: In autumn the solar plant delivers sufficient energy to

charge up buffer storage completely. The pellet stove boiler can then remain switched off

because the room of installation can be heated via a radiator using energy from the buffer

storage. This would not be possible without a radiator in the room of installation.

Proposed solution when installing Waterplus appliances in small rooms: If you have opted

for a Waterplus device and the designated room of installation does not meet the above

requirements, you can use a clock or room thermostat that

pellet stove boiler

radiator

heating circuit

chimney

Schematic drawing without buffer storage, control and hydraulic

equipment, installations room etc.

*nominal thermal output rating given in accordance with DIN 18891 (draft to DIN 18894)

room or interconnected rooms

of installation)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Frank SX waterplus S4 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Frank SX waterplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info