Bedienungsanleitung Wodtke Frank SX waterplus S4 (Seite 20 von 83) (Deutsch)

813089

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 20 / 83

5.10 Automatic operation “TW OFF” (only for Waterplus appliances)

Functional message: “TW OFF”

= appliance has been switched off via internal boiler sensor

= appliance has to be switched on manually via I/O key

= functional values can be called up via the “Menu” key

This function is only available with Waterplus appliances. “TW OFF”

means that the appliance is responding to a signal from the internal boiler

sensor inside the heat exchanger (temperature TW). The appliance has

been switched off via this sensor because the desired temperature in the

water heat exchanger has been exceeded. It will be

automatically switched on again later.

Note: If the appliance is now switched off via the I/O

key or through a class 1 error, it can no longer

respond to the external controller and will not start up

automatically again. Instead the display shows “G

OFF” and eventually the “stand-by dot” or, in the

event of an error, the “stand-by dot” flashing

alternately with the error code.

Tip: Do not switch the appliance off via the I/O

key when in the “TW OFF” state. The I/O key is

only intended for manual operation or as an

emergency switch in the event of errors.

5.10.1 Switching on and off via “TW OFF”

When the Waterplus appliance is switched off by an internal

controller after being in operation this is indicated by the messages

“G OFF” and “HE OFF” flashing alternately until the end of fan after-

run time. After this the display shows “TW OFF” alone.

When the appliance is restarted via an internal controller the display

shows “ON” and then for a few seconds the installed programme

version. If all is in order the appliance then enters preheating

programme “A” and eventually heating programme “H”.

5.11 Preheating programme “A”

= display shows “A” for preheating programme

= display shows flashing dot for feed screw operation

= display shows remaining minutes of preheating programme

In the preheating programme the ignition element is active for the

first 10 minutes after starting up, the pellets light after a few minutes

and the appliance runs to operating temperature. The air flow sensors

only become active after one minute, when the fan has reached

constant speed and an air flow has developed. You can adjust thermal

output in steps of 0.5 kW using the +/- keys. Thermal output setting only

becomes active on completion of the preheating programme when the

display changes to “H”. The appliance can also be switched off with the

I/O key during the preheating programme. It then enters the “G OFF”

state and eventually goes into stand-by.

Automatic operation no

longer possible because

appliance has been

switched to “stand-by”.

OFF

wodtke

A .

- 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Frank SX waterplus S4 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Frank SX waterplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info