Bedienungsanleitung Wodtke Frank waterplus S4 (Seite 14 von 83) (Deutsch)

813085

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 14 / 83

5.2 Manual selection of thermal output

The desired thermal output of the appliance can be adjusted at any time using the +/- keys. The

selected value stays valid even after switching off the appliance and remains so until a new

value is entered manually. After completing the preheating programme the appliance enters the

heating programme, where it automatically delivers the selected thermal output so long as

this setting is not overridden by an internal or external controller (see modulation). The

selected thermal output is displayed in kW and can be adjusted in steps of 0.5 kW.

Tip:

In buildings with rooms temperatures below +10 °C (for ex. holiday flats, new

buildings) we recommend setting thermal output to at least 4.0 kW.

5.3 Initial operation

Important information:

• In Germany the appliance must be inspected by the district master chimneysweep before its

initial operation. The master chimneysweep is responsible for issuing an operating licence.

• Always keep the firedoor closed, even when the appliance is cold.

• Never light the appliance with flammable or readily ignitable liquids.

• The door with the ceramic glass window becomes very hot during operation. Make sure that

nobody touches the window.

• The panels may also become hot after prolonged operation. Use the heat protection gloves

delivered with the appliance.

• Do not let children or adolescents come near the appliance unsupervised!

• All steel and cast metal parts of the stove have been coated and baked with a highly heat-

resistant enamel at the factory. During the stove’s initial operation the enamel will undergo

an afterdrying process. This can give rise to odour and fumes! In this case please observe

the following:

o Keep everyone including pets out of the room during this process, since the emitted

fumes may be harmful to health!

o Air the room thoroughly to allow the fumes to escape.

o During the afterdrying process the enamel will still be a little soft. Avoid touching

enamelled surfaces to make sure they don’t get spoilt.

o Let the appliance run for some time at a high level to allow the enamel to harden

completely.

Complete the installation procedure as described in the assembly instructions before filling

pellets into the fuel hopper. Fill the hopper with at least 5 kg of wood pellets.

Make sure that no objects have been left in the firebox or burner pot.

* This dot also lights up to indicate stand-by mode

Feed screw indicator flashes or lights up while feed screw is running*

“H” indicates that heating programme is running

Display of selected thermal output = 4.0 kW

4.0

H .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Frank waterplus S4 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Frank waterplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info