Bedienungsanleitung Wodtke Frank waterplus S4 (Seite 16 von 83) (Deutsch)

813085

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 16 / 83

5.4 Preparations / Lighting the stove

Note: The ignition procedure starts anew every time the appliance is switched on as well as

after a power failure, and it can take up to 10 minutes before the first flame becomes visible

(depending on how clean the burner pot is).

• Open the firedoor. Check whether the burner pot and firebox are free of soiling and pellets

and clean burner pot of pellets/ash/slag as necessary.

• Close the door.

• Open the combustion air pipe (if present).

• Switch the stove on by pressing the I/O key (after delivery the display will generally show “G

OFF” or the “stand-by dot”). Now pellets are fed into the burner pot. The stove lights

automatically via the ignition cartridge installed in the device. The pellets will start

burning after 5-10 minutes at the latest.

• If ignition fails (unburnt pellets in the burner pot), please first check whether the burner pot

is free of soiling (all air holes must be free; see also Chapter 0) and whether the fuel hopper

has been filled. If you are using the stove for the first time or the fuel hopper has run

completely empty it can take about 10 minutes before the pellets have passed the feed

screw. Clean the burner pot thoroughly before you try another start. Do not light the

pellets by hand . After a false start empty the burner pot completely and dispose of

the pellets and ash. Never return unburnt pellets from the burner pot to the fuel

hopper and never try to light them by hand.

 Danger of fire through glowing embers and/or overheating! 

Important information:

• Do not restart the appliance immediately after a successful start. Instead let it cool

down for at least 5 minutes at “G OFF” before restarting. In this way you will avoid

overheating the appliance.

• Be sure to keep the firedoor closed during the ignition phase and do not switch the

appliance on and off repeatedly.

5.5 Emergency operation with igniters

If the ignition cartridge of the appliance should fail you can still operate it when necessary by

using wodtke igniters. Light the pellets with the igniters as follows.

• Open the firedoor. Check whether the burner pot and firebox are free of soiling and pellets

and clean burner pot of pellets/ash/slag as necessary.

• Put wodtke igniters and a few pellets (never more than a handful) in the burner pot and

light them. Tip: Open the wodtke igniter a little before lighting it.

• Close the firedoor and open the combustion air pipe (if present).

• Switch the stove on by pressing the I/O key (after delivery the display will generally show “G

OFF” or the “stand-by dot”). Now pellets are automatically fed into the burner pot and the

flue gas fan starts running.

Caution:

Never use wood, paper, cardboard etc. or inflammable liquids for lighting the stove!

Never fill unburnt pellets or ash back into the fuel hopper.

Danger of fire through glowing embers!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wodtke Frank waterplus S4 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wodtke Frank waterplus S4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info