Bedienungsanleitung WOLF-Garten Ambition 400 E (Seite 22 von 201) (Alle Sprachen)

644603

Zoom out

Zoom in

Vorherige Seite

1/201

Nächste Seite

Intended use

This lawnmower is intended solely

- for mowing lawns in domestic and hobby gardens,

- for use in accordance with the descriptions and

safety information given in this operating manual.

Any other use is classed as an unintended use.

The user is liable for any damage arising from unin-

tended use.

Identication plate

Position

The identication plate is located on the deector

ap.

Note

The identication is considered as a docu-

ment. It must never be altered or obliterated.

Structure

1 Guaranteed sound level

2 CE label

3 Manufacturer

4 Device group

5 Model name

6 Model number

7 Serial number

8 Power

9 Engine speed in rpm

10 Weight

11 Rated voltage, kind of current, frequency

12 Disposal instruction

13 Protection class/IP code

14 Year of manufacture

Assembly

Attaching the handle

(Fig. A B C D E F G H I U)

Attention!

When folding the handle together or folding the

handle out, the cable may be damaged. Ensure

that the cable is not kinked.

ÎGrip in the handle recess of the deector

ap B 1 and pull the deector ap upwards until

the hook on the rear side of the casing and the

hook on the underside of the deector ap engage

with a loud click B 2.

ÎThen lower the deector ap again B 3.

3The grass is easily ejected through the resulting

gap between the deector ap and the casing

when mowing without the grass collector. You

can nd more information in the section “Mowing

without the grass collector”.

ÎNow x both handle mountings Ae to the bottom

part of the handle Al, see C 1.

ÎAttach the bottom part of the handle to the handle

mountings so that it clicks in C 2. Push the

handle up to the end of the handle mounting C 3.

ÎSlightly pull the bottom part of the handle apart at

its ends and push onto the threaded screws lo-

cated on the left and right side of the casing D 1.

ÎThen position the two washers Ag on the

threaded screws D 2.

ÎPush the threaded pins Aj into the quick-release

levers Ad, until the hole is visible E 1. Hold

these tightly with nger and thumb and screw

in the quick-release levers together with the

threaded pins in a clockwise direction E 2 until

there is a gap of approximately 10 mm E 3.

ÎSecure the bottom part of the handle, by folding

the quick-release levers upwards towards the

lawnmower E 4.

ÎAttach the top part of the handle Ak, by posi-

tioning it on the bottom part of the handle F 1.

Hold the top part of the handle with one hand

and with the other hand insert the screw Ah

from outside into the hole at the left side of the

handle F 2.

ÎPut the washer Ag on the screw from the other

side F 3.

ÎPush the threaded pin Aj into the quick-release

lever Ad, so that the hole is visible. Hold this

tightly with nger and thumb and screw in the

quick-release lever together with the threaded

pin in a clockwise direction until there is a gap of

approximately 10 mm F 3/4.

ÎPut the anti-kink protector Aa in place at the right

side of the handle, together with screw Ah which

must be inserted into the respective hole G 1.

12 13

Lawn Mower

A XXX E

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Ambition 400 E Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von WOLF-Garten Ambition 400 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info