Bedienungsanleitung WOLF-Garten Campus 30 V (Seite 11 von 30) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

638382

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

z If the connection cable is damaged during use it must be dis-

connected immediately. Do not touch the cable until it is dis-

connected.

z Switch off the lawnmower, pull the mains plug and wait for the

lawnmower to stop running if, for example:

– leaving the lawnmower

– unblocking a blade

– intending to check, clean or work on the lawnmower

– you have encountered a foreign object, in which case you

should check the lawnmower for damage and carry out any

necessary repairs.

– the lawnmower is vibrating heavily (switch off immediately

and ascertain the cause).

– you wish to change the settings or carry out cleaning work.

– you wish to check whether the connection cables have be-

come tangled or damaged.

– If the connection cable is damaged during use, it must be

immediately disconnected from the mains power supply.

Do not touch the cable before it has been disconnected

from the mains power supply.

Maintenance

1 Attention! Rotary cutter blade

Before all maintenance and cleaning work:

z Pull out the power plug.

z Do not touch running blades.

Disposal

Operation

Operating times

z Please check noise abatement regulations prevailing in your

country.

Feed cable through the strain relief

z Please feed cable through the strain relief.

Connecting to the mains (230 Volts, A.C., 50 Hz)

z The mower operates from any normal household mains sup-

ply, provided with a 16 Amps. fuse.

3 Note: Residual current protection device

These protection devices safeguard while touching

damaged wires, from insulation flaws and in certain cases,

also while damaging live wires.

z We recommend that the equipment only be plugged into

a power socket, which is protected by a residual current

protection device (RCD) with a residual current of not

more than 30 mA.

z Retrofit kits are available for old installations. Consult an elec-

trician.

Setting the working depth

1 Make sure the motor is switched off and the cutting

blades are not moving.

The working depth must be set correctly before the unit is usedfor

the first time. When assembling the wheels, ensure that they are

assembled in the eorreet positionfor the working depth setting.

Working depth setting when using the unit for the first time is po-

sition 1 of the wheel assembly.

3 Information:

Wear on the blades will make it necessary to re-adjust the

depth of cut at a later date. An optimum working depth is ob-

tained when the blades of the cutter are inserted 2-3 mm

into the ground. If the working depth is too deep, this can

overload the scarifier and cause damage. Ensure that the

depth of cut setting is correct.

z Unscrew wheels and move to the appropriate height setting.

Screw on wheels tightly.

Attach grassbox

Lift protective flap, hook grassbox with the hooks provided into the

holes in the chassis (see arrow), reattach protective flap.

Do not dispose of electrical equipment in domestic

waste. Recycle equipment, accessories and pa-

ckaging in an environment-friendly manner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Campus 30 V Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info