Bedienungsanleitung WOLF-Garten HS 54 E (Seite 9 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

638225

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Assembly

Protection shield - HS 43 / 54 E (Fig. M5)

If screws are fastened to the bottom plate, remove these. Fasten the

hand protector with the two included screws to the bottom plate.

Power connection

The machine can only be connected to a single-phase a.c. current

connection. The machine is protectively insulated in accordance with

classiﬁcation II of VDE 0740. Before using the machine ensure that the

mains current agrees with the operating voltage data on the machine’s

identiﬁcation plate.

Power Circuit Breaker

Machines which will be used in different outside locations must be

connected to a Power Circuit Breaker.

Safety Guard - Hs 40 E (Fig. M1)

Fit the enclosed safety guard in the slot on the hedgetrimmer. The safety

shield prevents touching the blades during operation. Hold tool with both

hands!

Mounting the bow-type handle - HS 43 / 54 E (Fig. M2-M4)

If there are screws ﬁxed to the mounting points, remove these ﬁrst.

Then, remove the shear protector and put the bow-type handle from the

front over the shearing system, and put it into the relief of the hedge

shears’ housing. (If necessary, pull the lower ends of the handle slightly

apart.) Take care that you do not squeeze the two parts of the bow-type

handle.To fasten the bow-type handle screw the two included screws

through the openings in the handle into the threaded holes of the housing

and fasten them tightly.

Operation

Operating times

Please consider the individual country speciﬁcations.

Instructions for use of the equipment

Do not use the trimmer in rain or for cutting wet hedges! Check the hedge

trimmer ﬂex and its connections before each and every use for visible

signs of damage (disconnect the power plug)! Do not use a faulty ﬂex.

Gloves

Protective gloves must be worn when using the hedge trimmer.

Securing the extension lead (Fig. B1)

Only use extension leads suitable for outside use. The cross section of

the wire (max. length of extension cord: 75m must be at least 1,5 mm

Secure the equipment ﬂex to the extension lead by means of a loop.

Extension leads longer than 30 m will reduce the performance of the

machine.

Two-hand safety switch (Fig. B2)

To switch on and to run the hedge trimmer you need both hands: The

switching bar in the rear handle as well as the switch in the front handle

must be depressed (A, B). If one of the switches is released, the shearing

blades will stop after ca. 0.5 seconds HS 40 E, 0.02 seconds HS 43 / 54 E.

Holding the hedge trimmer when in use (Fig. B3, B4)

This equipment will enable you to cut or trim bushes and hedges easily

and comfortably. Trimming of hedges

- Young shoots are best cut in a scythe movement.

- Older and stronger hedges are best cut in a sawing movement.

- Branches, which are too thick for the hedge trimmer, should be cut with

a saw.

- Sides of hedges should be cut upwards in a taper.

In order to achieve an even height

- Fix a guide line at the required height.

- Cut evenly over this guide line.

Expanded working height

If you want to reach higher or if you to above your head’s height, you

should take care of the following:

Attention: Take care to have a secure and safe standing position when

working with your hedge shears in order to avoid slipping and injury.

Always keep the shearing blades away from your body.

Optimum safety

The 5 special features:

two-hand safety switch, quick blade stop, protective cover, blade safety

rail and impact protector are ﬁtted to provide the hedge trimmer with

optimum safety features.

Two-hand safety switch (Fig. B2)

Quick blade stop

In order to avoid injuries through cuts, the blade will stop in max. 0.5 sec. HS

40 E, 0,02 sec., HS 43 / 54 E, when one of the two switches isreleased.

Blade safety rail (Fig. B5)

The cutting blade set back from the blade housing reduces the risk of

injuries due to unintentional body contact. As soon as the hedge trimmer

is switched off, the sharp cutting blades will stop immediately.

Impact protector (Fig. B5, A)

The extended guide rail prevents unpleasant shocks (blade recoil) being

transmitted to the operator due to impact with solid objects (wall, ground etc.)

Gear protection feature

If solid objects are caught in the cutting blade and jam the motor, switch

off the machine at once, disconnect the power plug from the power

socket, remove the object and continue with the work. The equipment

is also ﬁtted with an overload cutout, which protects the gears against

mechanical damage in the event of blade jams.

30. Have your power tools repaired by a qualiﬁed electrician

- This power tool corresponds to the applicable safety guidelines. Only an

electrician, using original replacement parts, may execute repairs; the use

of non-original replacement parts can cause accidents for the operator.

Safety instructions

31. Never attempt to use a machine that has parts missing, or a machine that has

an unauthorized modiﬁcation.

32. Never allow children to use the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten HS 54 E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info