Bedienungsanleitung WOLF-Garten Picco 32E (Seite 12 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

484184

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Operation

Operating times

Please check noise abatement regulations prevailing in your

country.

Connecting to the mains (230 Volts, A.C., 50 Hz)

The mower operates from any normal household mains

supply, provided with a 16 Amps. fuse.

Note: Use a residual current device (RCD) rated for a

residual current not greater than 30 mA.

Starting and Stoping

• Switch on motor with mowerplaced on level and firm ground

• not in high grass - alternatively tilt slightly

Switch-on motor

1. Depress button and hold (1).

2. Lift up bar (2).

3. release button (1).

Switch-off motor

Release bar (2).

Tips for mowing

•

Always let cable trail on the cut side of the lawn

• To prevent strips of grass from being left unmowed, the

cutting paths must always overlap a few centimeters

Hanging the grass bag

Only when the motor is not running and the

cutting blade is not moving.

1. Lift the protective ap.

2. Hang the grass bag in the chassis with the hooks in the

recesses (see arrow).

3. Replace the protective ap.

Emptying of Grassbox

The grassbox is full and should be emptied as soon as

grass clippings remain uncollected on the ground behind

your mower.

Note: Disconnect electricity by unplugging cable

at the socket-before proceeding.

Maintenance

Cleaning

Note: Disconnect electricity by unplugging cable

at the socket before proceeding. Attention: Keep

hands clear of moving blade.

Clean mower thoroughly after each mowing with cloth or

brush.

Do not spray with water.

Winter Storage

• Clean mower thoroughly before storing away.

• Have your mower thoroughly checked once a year by an

approved Service Centre.

• Do not store it in a wet or humid place.

Change of cutter blade

Note: always disconnect mains supply and wear

protective gloves before undertaking any work at

the cutter blades, cutter bar and blade coupling.

Change cutter blade using 10 mm spanner as illustraded.

Torque wrench setting for screws 8-10 Nm. Take care to

carry out this work thoroughly. Use original spare parts only.

Note: Sharpining of blades should be done by an

approved service centre as the correct balance of the

blade after sharpening is very important and ought to

be checked by an expert.

Selection of Cutting height

If possible, mow when grass is dry in order to protect turf. Do not

se cutting position too low when mowing very hight or wet grass.

We recommend an average cutting height of 3,4 cm.

Assembly

Fixing of handle

ATTENTION! Take care that theswitch cable does not

become caught and crused when folding the handle frame.

Mount grass bag

See illustrations.

Insert connection cable in the strain relief

Insert coupling of connection cable in the socket of the

switch. Then guide the cable from outside in a slight loop

over the peg of the strain relief assembly.

Setting the cutting height

Only when the motor is not running and the

cutting blade is not moving.

1. Lift all four bars up to stop.

2. Pull axles out of axle guides.

3. Firmly press axles into desired height guide.

4. Press in bars .

Note: All four wheels must be at the same height. same height.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Picco 32E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info