Bedienungsanleitung WOLF-Garten Power Edition 40 E-1 (Seite 13 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

638185

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

– unblocking a blade

– intending to check, clean or work on the lawnmower

– you have encountered a foreign object, in which case you

should check the lawnmower for damage and carry out any

necessary repairs.

– the lawnmower is vibrating heavily (switch off immediately

and ascertain the cause).

– you wish to change the settings or carry out cleaning work.

– you wish to check whether the connection cables have be-

come tangled or damaged.

– If the connection cable is damaged during use, it must be

immediately disconnected from the mains power supply.

Do not touch the cable before it has been disconnected

from the mains power supply.

Maintenance

1 Attention! Rotary cutter blade

Before all maintenance and cleaning work:

z Pull out the power plug.

z Do not touch running blades.

z Never spray down the lawnmower using water, especially not

at high pressure.

z Regularly check and tighten all visible screws and nuts, espe-

cially those relating to the cutting bar, to ensure a firm fit.

z Always have blades changed or re-sharpened by a specialist

workshop, since a balance test must be carried out as speci-

fied in the safety regulations following any removal of parts.

z Only use original WOLF spare parts. Otherwise we can’t gua-

rantee that your mower conforms to the safety regulations.

z Never park your lawnmower in damp rooms.

z For safety reasons, replace worn or damaged parts.

Disposal

Assembly

Fasten handle bars

1 Caution!

The cable can be damaged while folding up or pulling out

the handle bar.

z Inlay the cable in the bend protection .

z When adjusting the handle height take care that the ca-

ble is not crimped

1. Fold the bottom part of the handle up and screw it tight with

the two hand wheels .

2. Set the handle to the desired height .

3. Fold the upper part of the handle out and screw it tight with the

wing nuts .

Mount the collecting bag

1. Place the chute (1) on the collecting bag flap (2) .

2. Press the chute from behind onto the collecting bag flap. The

chute is ready for use as soon as it locks into place .

Operation

General

Operating times

z Please check noise abatement regulations prevailing in your

country.

Feed cable through the strain relief

z Please feed cable through the strain relief .

3 Note: WOLF Flick-Flack®

WOLF Flick-Flack® keeps the cable away from the cutting

unit .

Set cut height

1 Attention! Rotary cutter blade

Undertake work/adjustments on the equipment only after

the motor is switched off and the cutting tool has come to a

standstill.

1. Pull the lever out (1).

2. Set the desired cutting height .

3. Press the lever back in (2).

Selection of Cutting height

z If possible, mow when grass is dry in order to protect turf. Do

not se cutting position too low when mowing very hight or wet

grass.

z We recommend an average cutting height of 50 mm.

Do not dispose of electrical equipment in domestic

waste. Recycle equipment, accessories and pa-

ckaging in an environment-friendly manner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Power Edition 40 E-1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info