Bedienungsanleitung WOLF-Garten Power Edition 46 BA (Seite 12 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Türkisch)

638060

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

z For safety reasons replace worn out or damaged parts.

z NOTE! Always have blades replaced or sharpened by a

WOLF-Garten Service Centre, as a blade balance test must

be performed in accordance with safety regulations and the

blade retaining bolt must be tightened to a specified torque.

z Wear suitable work gloves when carrying out the above work,

especially when handling the blade.

Assembly

Fixing of handle

1 ATTENTION! Take care that the switch cable does not

become caught and crused when folding the handle fra-

me.

1. Fold the handle bar toward the back .

2. Set the handle to the desired height and tighten the two wing

nuts

3. Fold the upper handle up and screw it tight with the two wing

nuts .

Mount grass catcher

z See illustrations.

Operation

Operating times

z Please check noise abatement regulations prevailing in your

country.

Starter cord assembly

1. Lift and hold operator presence bail arm (2).

2. Pull the starter rope slowly to the holding bracket.

Twist the cord through the holder .

3 Always remove the starter cord from the holder before

folding the mower handles.

Oil Fill

1 Check oil level with mower standing on level ground.

Fill crankcase with quality oil SAE 30 up to the mark „Full“

on dipstick. (Do not overfill.) Capacity approx. 0,6 litre.

Screw in dipstick according to illus.

Filling with fuel

1 Caution! Rotating blades

Settings only to be carried out on the machine with the mo-

tor switched off and with the working tools at a standstill.

z Use only normal lead-free petrol (not Super unleaded).

z Avoid spilling petrol.

z Do not inhale the vapour.

Hang up collection bag

1 Attention! Rotary cutter blade

Undertake adjustments on the equipment only after the

motor is switched off and the cutting tool has come to a

standstill.

1. Lift the protective flap.

2. Hang the grass bag in the chassis with the hooks in the re-

cesses (see arrow).

3. Replace the protective flap.

Set cut height

1 Attention! Rotary cutter blade

Undertake work/adjustments on the equipment only after

the motor is switched off and the cutting tool has come to a

standstill.

1. Place hand into handle bar and depress button (1).

2. Lift or lower chassis until it engages into required position (2).

Selection of Cutting height

z If possible, mow when grass is dry in order to protect turf. Do

not se cutting position too low when mowing very hight or wet

grass.

z We recommend an average cutting height of 40-50 mm.

Start

z On a flat surface, if possible not in high grass.

1. Throttle lever (1) to “Betrieb” (= running).

2. Raise and hold the safety bracket (2).

3. Pull starter grip and return it slowly by hand.

Wheel drive (Power Edition 40 BA, Power Edition 46 BA)

1. Wheel drive on: Raise drive bracket (3).

2. Wheel drive off: Relapse drive bracket (3).

Stop Motor

z Release safety bracket (2).

3 If the motor does not start in cold weather, press the

primer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten Power Edition 46 BA Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info