Bedienungsanleitung WOLF-Garten SDE 2500 (Seite 10 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

517925

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Switching on / off

Press the green button to switch on (2)

z Press the red button to switch off (3)

3 The machine has a circuit breaker to prevent switching

back on unintentionally after a power cut.

Overload protection

3 An overloading of the appliance (e.g. culminating in the

blocking of the blades) can lead to the standstill of the

appliance after a few seconds. To protect the motor

from damage the appliance is automatically discon-

nected from the mains by the overload protection.

z Before putting into operation again wait for at least one

minute before immediately pressing the reset button

(1) and then ON/OFF switch. If the motor does not

start, clean the collection hopper (see Maintenance).

Special instructions for chopping

z Chop branches, twigs and wood shortly after cutting (this

chopped material will become very hard once it has dried out,

therefore the maximum diameter which can be processed is

less).

z Remove the side shoots on severely ramified branches.

z When processing garden or kitchen waste with a high water

content with a tendency to stick, crush alternately with wooden

chopping material to avoid blocking the appliance.

z Do not allow the chopping material in the area of the discharge

opening to accumulate too high. This can lead to material

which is already chopped blocking the discharge channel.

This can cause a kickback of the material through the filling

opening.

z Ensure that the maximum branch diameter for processing per-

mitted for your appliance is observed.

z The blade unit pulls in the chopping material largely by itself.

z Do not overload or block the motor in the case of tough

branches by frequently pulling back the branch.

Maintenance

General

1 Remove the mains plug before any maintenance and

cleaning work!

When servicing the cutting tool ensure that it can still

always run on even when the motor is switched off.

Wear protective gloves.

z Store the appliance in a dry location out of the reach of chil-

dren.

General cleaning information

1 Remove the mains plug before any maintenance and

cleaning work!

z Handle the appliance with care and clean it regularly to pro-

long its service life.

z Keep the ventilation slits clean and dust-free.

z Only use a warm and moist cloth to clean the appliance as well

as a soft brush.

z Do not allow the appliance to get wet and do not spray with

water.

Cleaning the collection hopper

1 Remove the mains plug before any maintenance and

cleaning work!

1. Unscrew the knob and fold the casing upwards to open .

2. Clean the cutting and discharge area of all objects which could

block the blades.

3. Close the casing again and tighten the knob .

4. Press the reset button before activating the ON/OFF switch.

Safety locking device

z The chopper is equipped with a safety locking device at the

lock between the casing and the motor casing.

z In the event that the casing does not close flush to the motor

casing, the motor is stopped by the safety locking device.

z In such a case, proceed as follows:

– Unscrew the knob and fold the casing upwards to open .

– Carefully clean the contact surfaces.

– Close the casing again and tighten the knob .

Changing blades

1 Remove the mains plug before any maintenance and

cleaning work!

When servicing the cutting tool ensure that it can still

always run on even when the motor is switched off.

For safety reasons, always have the blades changed by

an authorised service centre.

1. Unscrew the knob and fold the casing upwards to open .

2. In order to change the blades insert the hexagon spanner

(1) in the slot on the retaining plate and through the cover.

3. Loosen the two screws with the Allen spanner

(2) and

take out the worn blades.

4. Insert the new blades and tighten the screws.

1 Remove both the Allen and hexagon spanner after com-

pleting the change.

5. Close the casing again and tighten the knob .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten SDE 2500 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info