Bedienungsanleitung WOLF-Garten UV 28 EV (Seite 9 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

638373

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Safety instructions

• Attach connection cable to traction relief. Make sure that in does

not rub against edges, pointed or sharp objects. Do not squeeze

cable through door or window gaps.

• Switching devices must not be removed or bridged (e. g. tying of

switching lever to guide spar).

4. Starting up

• Only switch on motor when your feet are at a safe distance from the

cutting tools.

• Do not tilt the aeriator when operating the switch unless absolutely

necessary. If it is necessary tilt the aeriator as little as possible and

always in such a way that the aeriator remains between you and the

blade.

5. During aeriation - for your safety

• Warning, Danger! Cutting tool is lagging!

• Adhere to the safety distance given by the guidance spars.

• Only switch on motor when your feet are at a safe distance from the

cutting tools.

• Always make sure that you have a safe footing, especially on

slopes. Never run, always walk slowly.

• Do not use the aeriator on steep slopes.

• Keep cable away from operating tool when aeriating.

• Always move aeriator horizontally to the slope, never up and

down.

• Switch off aeriator when tilting or transporting.

• Never use the aeriator when protective devices or housing parts are

damaged or missing.

• Before lifting or removing the aeriator switch off motor an wait until

the operating tools have come to a complete standstill.

• Before removing the grassbox or adjusting of the operating height

switch off motor and wait for the complete standstill of the operating

tools.

• Replace worn or damaged blades as a complete set. Observe

installation instructions. For safety reasons always use original

spare parts.

•

Maintenance and cleaning procedures on the aeriator as well as remov-

ing the protective devices may only be carried out when the engine is

switched off.

• Never store the aeriator in damp surroundings or near open ame.

• Should have run over an object with the aeriator it should be exam-

ined by a specialist (see list of repair shops) for safety reasons.

• If the connection cable is damaged during use it must be dis-

connected immediately. Do not touch the cable until it is discon-

nected.

Assembling bottom handle part (fig. M1)

Insert securing screw (A) from inside through the left side

element, so that both projections catch in the recesses (1).

Position insulation element (B) from outside; the two nubs

must catch in the holes of the side element (2). Position

handle element (M) in the insulating element (B). Place

insulating element (C) so that the large opening points to

the outside. Then press washer (D) into the opening of the

insulating element (C) and tighten wing nut (G).

Assemble the right handle element in the same order.

Assembling top of handle (fig. M2)

Assembly

Attaching switch, strain relief and clips (fig. M3)

Fold up switch bracket (1) and position switch (H) on the

upper handle element so that the two nubs catch in the holes

(2). Close switch bracket (1) and insert cable strain relief (I).

Then fasten switch (H) and cable strain relief (I) with the two

screws (K). Fasten switch cable (3) with the clips (L) on the

handle rod.

Attaching protective flap (fig. M4)

Place protective flap (O) on the cover (1). Then press retainer

slots (2) into the fastening flaps (3) on the cover (1).

Operation

Operating times

Please check noise abatement regulations prevailing in your

country.

Setting the working depth (fig. B1)

The working depth is adjustable to 3 heights (1 = 3 mm, 2 = -3

mm, 3 = -9 mm). Pull adjustment arm (A) away from side cover

and allow to catch in desired position (B). Adjust the height

alternately left and right by only 1 position. The adjustment

arms must always be in the same height position.

Recommended working depths

(Fig. B1)

Lawn condition Working position

Transport / uneven lawn surface 1

Clean lawn surface 2

Worn blade 3

Insert connection cable in the strain relief (fig. B2)

Insert coupling of connection cable (3) in the socket of the

switch (H). Then guide the cable (4) from outside in a slight

loop over the peg (5) of the strain relief assembly (I).

Connection to the power outlet

(230 Volt AC, 50 Hz). The machine can be connected to

any power outlet that is protected by a 10 amp fuse (or line

protecting switch type B).

Note:

Use a residual current protection device with a residual

current of no more than 30 mA.

Motor on (fig. B2)

Press button (1) and hold.

Lift lever (2) and release button (1).

Motor off (fig. B2)

Release lever (2).

Attaching catch bag* (fig. B3)

Lift protective flap (O). Hang catch bag (1) with the hooks on

both bolts** of the side elements.

(* TK 33 3615 060, accessory at additional cost, ** bolts

included with catch bag)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten UV 28 EV Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info