Bedienungsanleitung WOLF-Garten UV 30 EV plus (Seite 13 von 30) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

638376

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Maintenance

Remove spark plug/mains plug cap before attemting any

work to the unit.

Clean the unit thoroughly with a brush after each use. Do not

spray with water. Store unit in a dry room.

We recommend

Allow a WOLF-service centre to check the unit in the

autumn.

Operation

Adjust operating depth (Fig. B)

Only with motor switched off and non-mowing aeriating roller.

The operating depth must be adjusted to the corresponding

grass and ground conditions.

• Move operating lever towards front (Fig. B, 1).

•

Adjust operating depth with turn handle to the desired depth (+).

Aeriating test:

- Pull operating lever up again.

- Start tool (Fig. C).

- Push operating lever slowly forward (Fig. D).

- Move tool slowly into operating direction.

- On hearing stones being hit or blocking of the motor imme-

diately switch off tool.

- Turn rotating handle 1–2 rotations towards the left (–) - (One

revolution corresponds to 1,5 mm.)

- Start aeriating test again.

• When used regularly the aeriating depth may be adjusted

according to the wear of the blade (+).

Recommended working heights

well kept lawns with stone-free, soft ground

• Set tool exactly to ground height

stony, untidy lawns

• Set tool to ground height

• Increase working height if stones are thrown up

unkempt, extremely mossy lawns

• Start with a high working height

• Do not overload appliance (increase working height if motor

blocks)

• Cut vertically and crossways several times

• Re-sow with WOLF >>Loretta<< lawn seeds

Attach grassbox* (Fig. F)

Lift protective ap, hook grassbox with the hooks provided into

the holes in the chassis (see arrow), reattach protective ap.

*Grassbox TK-VV 3632 060 - (accessory, available at

additional cost)

Starting up the engine/Scarifying

1. Depress button (Fig. C, 1) and hold.

2. Lift up bar (Fig. C, 2) and release button (Fig. C, 1).

3. Place lever (Fig. D) slowly into forward position.

4. Switch-off motor: Release bar (Fig. C, 2).

Important: Place the cable rmly off the lawn or on the

already cut side of the lawn when starting to mow.

Turning (UV 32 EV, UV 34 E)

The cable relief holder enables you to move the cable from

one side of the handle frame to the other. Thus you ensure

that the cable always trails on the ride of the lawn already cut

– and not in front of the machine (Fig. E).

Operating times

Please check noise abatement regulations prevailing in your

country.

Connecting to the mains (230 Volts, A.C., 50 Hz)

The mower operates from any normal household mains

supply, provided with a 16 Amps. fuse.

Note: Use a residual current device (RCD) rated for a

residual current not greater than 30 mA.

Inserting power cable into cable holder (Fig. A)

Insert the power cord into the strain relief as shown in the

illustration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten UV 30 EV plus Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info