Bedienungsanleitung WOLF-Garten UV 40 B (Seite 11 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

517907

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

z Take particular care when turning the machine or when pulling

it towards you.

z Stop the working tools if:

– the machine needs to be tilted for transport.

– if areas other than grass are to be crossed

– when transporting the machine.

z Never use the machine with damaged or removed protection

devices.

z Make sure that there is adequate distance between your feet

and the working tools.

z When starting the engine do not tilt the machine, unless the

machine needs to be lifted during this process. In this case tilt

only as much as necessary, and only lift the side away from

the operator.

z Never put your hands or feet near the rotating parts.

z Always keep away from the ejection opening.

z Never lift or carry the machine when the engine is running.

z Stop the engine and remove the sparking plug lead:

– before removing blockages or obstruction in the ejection

channel,

– before checking the machine, cleaning it or doing work on

the machine

– if foreign bodies are struck. Check the machine for damage

and undertake the required repair before re-starting and

working with the machine

– if the machine starts to vibrate excessively.

– when leaving the machine.

– before filling up with petrol.

Maintenance and storage

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

z Make sure that all nuts, bolts and screws are tightened

properly in order for you to make sure that the machine is in a

safe working condition.

z Never store the machine with petrol in the fuel tank inside a

building in which it may be possible for petrol vapour to come

into contact with fire or sparks.

z Allow the engine to cool down before storing the machine in

enclosed spaces.

z In order to prevent fire, keep the engine free from grass, straw,

moss, leaves or escaping grease.

z Check the machine regularly and replace worn or damaged

parts for safety's sake.

z If the fuel tank needs to be emptied this should be done in the

open air.The drained fuel must be stored in a special container

for fuel or should be disposed of carefully.

Assembly

Fixing the grab handle

1 Caution!

When collapsing and unfolding the grab handle, the cable

could be damaged.

z Take care that you do not kink the electrical cable and

the Bowden cable.

z Fold the grab handle down in accordance with the

illustration and tighten it in place with the wing nuts.

Operation

Operating times

z Please observe the regional regulations.

z Request the operating times from your local authorities.

Topping up the oil

z Please check the oil level before scarifying.

z Before using for the first time, you must add 0.6 l. VO-4T four-

stroke oil up to the mark.

Filling with fuel

1 Caution! Rotating blades

Settings only to be carried out on the machine with the

motor switched off and with the working tools at a standstill.

z Switch the motor off and pull off the sparking plug lead.

z Use only normal lead-free petrol (not Super unleaded).

z Avoid spilling petrol.

z Do not inhale the vapour.

Setting the working depth

1 Caution!Rotating blades

Settings only to be carried out on the machine with the

motor switched off and with the working tools at a standstill.

z switch the motor off and pull off the sparking plug lead.

3 Recommendations on working depth:

prepared areas with stone-free, soft ground conditions

z Match the working depth exactly to ground level

(factory setting)

stony, unkempt areas

z Set the working tools to ground level

z If stones are thrown up, set a reduced working depth

rough ground, very mossy ground

z start with a small working depth

z do not overload the machine (if the motor stalls use a

smaller working depth)

z scarify several times at right angles

z re-seed with WOLF Lawn Seed (e.g. "Loretta")

1. Put the setting lever back into the transport position

(1)

2. Increasing the working depth (cutters towards the

ground)

(1)

Turn the handwheel "Working Depth Adjustment" to the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten UV 40 B Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info