Bedienungsanleitung WOLF-Garten XQ 4 HW (Seite 15 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

638047

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Maintenance

General

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

z For safety reasons, replace any worn or damaged parts.

When replacing, follow the instructions for installation

z Check all the visible fastening bolts and nuts regularly to be

sure they are snug and tighten them.

z Only use spare parts made by WOLF; otherwise you do not

have a guarantee that your mower meets safety regulations.

Cleaning operations and blade change

1. Pull off the sparkplug connector!

2. Raise the cutting height to its highest position .

3. For cleaning and changing the blade, tip the mower to the side

as illustrated .

Sharpening and changing blade

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

1 Attention!

An unbalance can develop after regrinding of the blade.

z Always regrind the blades in a specialist workshop,

because an unbalance check should be undertaken

according to the safety regulations.

– Always change blades in a specialist workshop. A torque

spanner of 17 mm is mandatorily required.

Fastening torque of the screws: 38-42 N-m.

Adjusting the Bowden cable coupling

1. Raise the drive bracket (2) app. 2 cm and hold.

2. Loosen the locking nut (1).

3. Turn the setscrew (2) left until the drive wheels are blo-

cked when you pull the mower backwards.

4. Tighten locking nut (1).

Change oil only

z While engine is warm and fuel tank empty.

z Change oil after the first 5 working hours. There after change

engine oil every 25 working hours and at the end of the mo-

wing season. Change engine oil more frequently if working un-

der extreme and dusty conditions.

1. Remove oil filler cap.

2. Tilt machine slowly to side and allow oil to drain from the

crankcase through the filler.

3. Oil Fill .

Cleaning of Spark Plug

z Check and clean regularly

z Reset plug gap as required (0,76 mm).

Cleaning of air filter

Refer to the engine manufacturer‘s handbook supplied.

Storage in winter

z Drain the fuel tank.

z Drain the carburettor.

– This can be done by starting the engine and allowing it to

run until it stops of its own accord.

z Clean the mower thoroughly.

z Change the oil.

z Preserve the engine:

– Unscrew the sparking plug and pour one dessert spoon of

engine oil into the sparking plug opening

– Pull the starting cord slowly all the way (oil distribution in the

cylinder)

– Screw the sparking plug back in position (do not replace the

sparking plug lead)

z Store the mower in a cool and dry location.

z The mower should be checked by a WOLF customer service

workshop in the autumn.

Spare parts

Ordering number Designation of the item Description of the item

4218 065 Grass catcher

4218 094 Vi 48 S Replacement blade 48 cm

2058 305 Champion RJ 19 LM Spark plug

2056 305 Air filter

4180 091 HD SAE 30 (VO 4T) Motor oil 0,6 l

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten XQ 4 HW Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info