Bedienungsanleitung Wolfgang Tools CAP110 (Seite 2 von 2) (Englisch)

805648

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5. Inspect unit for cracks, pin holes, or other imperfections that

could cause air compressor to become unsafe.

6. Never cut or drill holes in the air compressor.

7. Make sure the hose is free of obstructions or snags.

8. Entangled or snarled hoses can cause loss of balance or footing

and may become damaged.

9. Use the air compressor only for its intended use. Do not alter or

modify the unit from the original design or function.

10. Always be aware that misuse and improper handling of this air

compressor can cause injury to yourself and others.

11. Never leave an air compressor unattended with the air hose

attached to the item being inﬂated.

12. Do not continue to use a air compressor or hose that leaks air or

does not function properly.

13. Always disconnect the air supply and power supply before

making adjustments, servicing an air compressor, or when an air

compressor is not in use.

14. Do not attempt to pull or carry the air compressor by the hoses.

15. Always follow all safety rules recommended by the manufacturer

of your air compressor, in addition to all safety rules for the air

compressor. Following this rule will reduce the risk of serious

personal injury.

16. Household use only.

17. Do not use air compressor as a breathing device.

18. Never direct a jet of compressed air toward people or animals.

Take care not to blow dust and dirt towards yourself or others.

Following this rule will reduce the risk of serious injury.

19. Protect your lungs. Wear a face or dust mask if the operation is

dusty. Following this rule will reduce the risk of serious personal

injury.

20. Do not use this air compressor to spray chemicals. Your lungs can

be damaged by inhaling toxic fumes.

21. Check damaged parts. Before further use of the air compressor

or air tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and

perform its intended function.

22. Check for alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions that may

affect its operation. A guard or other part that is damaged should

be properly repaired or replaced by an authorized service center.

Following this rule will reduce the risk of shock, ﬁre, or serious

injury.

23. Constantly stay aware of cord location. Following this rule will.

reduce the risk of electric shock or ﬁre.

24. Risk of bursting. Carefully monitor objects during inﬂation.

25. To reduce the risk of overinﬂation, use a reliable pressure gauge

periodically during inﬂation. The pressure gauge on the air

compressor is for reference only and is therefore not binding for

exact values.

26. Never leave the air compressor unattended during inﬂation.

27. Allow pump to cool for ﬁve (5) minutes after each ﬁve (5) minutes

of continuous use. Never block the inﬂating or deﬂating outlets

while operating.

28. Save these instructions. Refer to them frequently and use them

to instruct others who may use this air compressor.

29. If you loan someone this air compressor, loan them these

instructions also.

USE AND FUNCTION (FIG. 1)

INSTALLING AND RELEASE THE BATTERY PACK

Set Forward/Reversing lever to the center (off position). Slide

charged battery pack into the housing until the battery pack locks

into position. To remove the battery pack, press the battery pack

release button and slide the battery pack forward.

CHARGING THE BATTERY

Do not use other battery chargers. The supplied battery charger is

designed for the Lithium-ion battery in your machine. This charger

is suitable for indoor use only.

NOTE: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery with the

battery charger before using your power tool for the ﬁrst time. The

Lithium-ion battery can be charged at any time without reducing

its service life. Interrupting the charging procedure does not

damage the battery.

The charging procedure begins as soon as the mains plug of the

battery charger is plugged into a socket outlet and the charge

connector is plugged into the socket on the side of the battery.

The battery charge indicator on the plug shows the charging

process. During the process the indicator shows a red/green light.

When the battery charge indicator shows a green light, the battery

is fully charged.

During the procedure, the handle of the tool warms up, this is

normal.

The battery requires 3 - 5 hours to fully charge.

Disconnect the battery charger from the mains supply when not

in use.

NOTE: The power tool cannot be used during the charge procedure.

START SWITCH AND SELF-LOCKING SWITCH

1. When press start switch, push self-locking switch up, which will

make the switch in LOCK- ON. This guarantees the safety for the

user and of the tool.

2. After the pressure enough, pressing the start switch, then the

self-locking switch will sprang back down.

LED WORKING LIGHT

CAUTION: Do not look directly into the light or the source of light.

ACCESSORIES

The supplied accessories perform a variety of functions. The

tapered adaptor can be used on smaller pinch valves to inﬂate

small items like children’s toys, which usually require the user to

inﬂate them by blowing air into them. The sport ball needle can

be used to inﬂate any type of sports ball or any other item that

requires an inﬂation sport ball needle.

NOTE: When inﬂating items of 0.7 bar (10 psi) or less, inﬂate in

short bursts and check after each burst by feel or with a calibrated

measuring device to determine accurate pressure.

USING THE AIR COMPRESSOR

1. Install the battery pack.

2. Position air chuck clamp in the unlock position perpendicular to

the air hose.

3. Place the air chuck on the valve stem.

4. Push the air chuck down so that the threaded section of the

valve stem is inside the air chuck.

5. Clamp the end of the air chuck down onto the valve stem by

pressing air chuck clamp down until it stops or is parallel with

the air hose.

MAINTENANCE AND STORAGE

CAUTION!

Do not use any products that may damage the

unit (abrasives, corrosives, alcohol, steam cleaners,

abrasive rags, scrapers, etc.). Do not put the unit in

a dishwasher for cleaning!

The unit must be completely switched off, disconnected and cooled

before cleaning.

MAINTENANCE

• When necessary, you can clean the unit body with a soft,

dry cloth.

• Check that the machine has not been damaged. If the machine

is damaged, we recommend you to call a qualiﬁed technician to

inspect the machine and make necessary repairs.

• When necessary, charge the battery.

STORAGE

Store the tool and its accessories in a dry, frost-free place.

The tool should always be kept out of the reach of children.

We recommend to store the tool in its original packaging or

covering it with a suitable fabric to protect it from dust.

TECHNICAL SPECIFICATIONS

MODEL CAP110

Voltage 18 Vdc

Maximum pressure 7.5 bar

Charger Input 100 - 240V ~ 50/60Hz, 0.3A

Output 20V dc 0.3A

DECLARATION OF SOUND LEVEL ACCORDING TO EN 60745

Sound pressure level LpA, d: 81 dB(A) K = 3 dB(A)

Sound power level LWA, d: 95 dB(A) K = 3 dB(A)

DECLARATION OF VIBRATION LEVEL ACCORDING TO EN 60745

Vibration level (m/s2)3.6

Uncertainty (m/s2)K = 1.5

Quick Recharging Battery voltage 18V DC

Charging time 3 - 5 hours

WARNING:

The declared vibration total value has been

measured in accordance with standard EN 60745

test method and may be used for comparing one

tool with another; The declared vibration total value

may also be used in a preliminary assessment of

exposure.

That the vibration emission during actual use of

the power tool can differ from the declared total

value depending on the ways in which the tool is

used; and of the need to identify safety measures to

protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

Mascot Online BV

Bellstraat 7

3861 NP Nijkerk

The Netherlands

www.wolfgang-tools.nl

Made in PRC

INSTRUCTIONS FOR THE PROTECTION OF THE

ENVIRONMENT

(WEEE, the waste electrical and electronic

equipment directive)

Your product has been manufactured from high

quality materials and components which can be

recycled and used again. At the end of its life, this

product cannot be disposed of in normal domestic

waste, but must be taken to a special collection

point for the recycling of electrical and electronic

equipment. The waste container marked with a

cross symbol on the item, in the user manual and on

the packaging informs you of this. The raw materials

used are suitable for recycling.

By recycling used appliances or raw materials you are making an

important contribution to the protection of our environment.

You can ﬁnd out the location of your nearest collection point

from your local council.

Do not dispose of batteries in your household waste.

To dispose of the batteries, take them to your local recycling

station. Contact your local government ofﬁces for details.

EN - manual Luchtpomp 18V CPS01180000MO.indd 2 10/01/2018 14:12

Wolfgang Tools CAP110 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wolfgang Tools CAP110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info