Bedienungsanleitung Woods AC Cortina Silent 12K (Seite 16 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

705112

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Operating Instructions

Installation

If the unit has been transported horizon-

tally, keep it in an upright position for 4

hours before using it.

Place the unit on a at and solid surface.

Do not install the unit in bathrooms or

other wet environments.

Make sure that air ow isn’t blocked,

always keep at least 50 cm distance to

surrounding surfaces.

INSTALLING THE EXHAUST HOSE

1. Extend one end of exhaust hose, screw

the end without slot of round connector

onto it with anticlockwise direction at

least 3 laps.

2. Extend another end of exhaust

hose, screw the adapter onto it with

anticlockwise direction at least 3 laps.

3. Extend the exhaust hose and lead it

outside through a door or window.

USING THE WINDOW KIT

1. To use the window kit, open the

window and place the window kit either

horizontally or vertically, depending on

the window.

2. Adjust the length of the window kit and

fasten it with the screws.

3. Shut the window and attach the adapter

on the exhaust hose to the window kit.

USING THE WINDOW KIT

Before using your remote, install the AAA

batteries into remote control.

1. Press and slide the battery cover on the

back of the remote control, then you can

remove the cover.

2. Insert two new alkaline AAA batteries

into the battery compartment, being

sure to note the proper polarity.

3. Put back the battery cover, making sure

the locking tab clicks into place.

Use alkaline batteries only. Do not use

rechargeable batteries.

When replace batteries, always replace

both batteries with new batteries, do not

mix old and new batteries.

If the air conditioner will not be used for

an extended period of time, remove the

batteries from the remote control.

Operating instructions

1. Starting the unit. Press the POWER

button to start and stop the unit.

2. Select mode. The unit has 4 dierent

modes: cooling, dehumidify, energy

conservation and fan mode. Press MODE

on the control panel or remote control

to select mode.

• Cooling mode: Set desired temperature

with the arrows on the control panel or

the remote control. Set temperature is

shown in the display.

• Dehumidify. In dehumidify mode,

the fan will run on low speed only.

Temperature cannot be set.

• Fan mode. The compressor stops and

only the fan will run. Temperature

cannot be set.

• Energy conversation mode. Low

energy consumption under Energy

Conversation mode. When the ambient

temperature is higher than the set

temperature, the unit operates in cool

mode. When the ambient temperature

reaches the set temperature, the

compressor stops running and the

upper fan also stops running. After 2

minutes and 30 seconds, the upper fan

will run at low speed for 30 seconds. If

the compressor does not start (that is,

the ambient temperature is lower than

the set temperature), the upper fan will

repeatedly operate in this mode (stop

for 2 minutes 30 seconds / low wind

operation for 30 seconds).

3. Set timer.

• To set timer for shut o, press the TIMER

button when the unit is operating.

• To set timer for start, press the TIMER

button when the unit is switched o.

Set time with the up and down arrows on

the control panel or remote control. When

the timer is activated, a light is shown on

the control panel.

4. Set fan speed. Press the SPEED button

on the control panel to choose fan

speed. On the remote control, press the

FAN button to choose fan speed.

5. Celsius/Fahrenheit On the control panel,

press the up and down arrows at the

same time to switch between Celsius

and Fahrenheit.

6. Sleep mode. Use the sleep mode during

the night and the unit will not disturb

your sleep. When in cooling mode, press

the TIMER and UP together to enter

sleep mode. On the remote, press the

SLEEP button. Press again to deactivate.

7. Auto swing function. Press the TIMER

and SPEED button at the same time to

activate swing function. On the remote,

press the Auto-swing button. Press again

to deactivate.

8. Auto clean function. Press the AUTO-

CLEAN button on the remote control to

clean the unit internally. The unit will

clean for 3 minutes before shutting o.

PROTECTION FUNCTIONS

Automatic defrost

The unit will automatically defrost when

needed. In defrost mode, the display

shows E4 and no buttons except the

POWER button are active.

Compressor protection

The unit has a compressor protection

function causing a 3-minute start delay

after the unit is restarted.

Water full alarm

When the water tank is full, the unit will

stop working. A water-full indication light

is shown in the display and a warning

sound is heard. Empty the water tank and

restart the unit.

FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Woods AC Cortina Silent 12K Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info