Bedienungsanleitung Worcester-Bosch GB162-80 (Seite 16 von 72) (Englisch)

697434

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Installation

6720813171 (2016/05)16

▶ Install the gas valve connector 1" [1] (accessory).

▶ Install the gas valve [2] onto the gas pipe. Use a gas valve with a

minimum diameter of 1".

Fig. 14 Making the gas connection

[1] Gas valve connector 1"

[2] Gas valve 1"

▶ Connect the main gas pipe to the gas connection making sure it is not

under stress. Use a gas pipe of at least Ø 22 mm.

▶ Make the gas connection according to the country-specific standards

and regulations.

▶ Carry out gas leak test on gas connection using leak detection spray

and purged as described in IGE/UP/1b.

Installing the heating flow and return pipe

The central heating system should be installed in accordance with

BS 6798 and, in addition, for small bore and micro bore systems,

BS 5449 or EN 12823.

▶ Connect the flow pipe with a flat rubber seal installed to the CHF

(CH boiler flow) connection [1] making sure it is not under stress.

Use a flow pipe with a minimum diameter of 1½".

▶ Connect the return pipe with a flat rubber seal installed to the CHR

(CH boiler return) connection [2] making sure it is not under stress.

Use a return pipe with a minimum diameter of 1½".

Fig. 15 Connecting the boiler flow and return

[1] CH boiler flow

[2] CH boiler return

[3] Isolating valves

[4] Drain cock

[5] Gas valve

[6] Pressure relief valve

[7] Condensate trap

[8] Pump

[9] Non-return valve

[10] Dirt filter

8.2.4 Installing the differential pressure controller

In situations where there is no low loss header, installing a bypass with a

differential pressure controller would not be required.

If a low loss header is present, it may be required -depending on the

situation - to install a bypass with a differential pressure controller to the

secondary side of the low loss header. This serves to protect the

secondary pump against overheating as a result of insufficient flow.

8.2.5 Installing the isolating valves

▶ Install a isolating valve for maintenance and repair purposes in both

the boiler flow and return circuits ( fig. 15, [3]). Use isolating

valves with a minimum diameter of 1½".

8.2.6 Installing the drain cock

▶ Connect a drain cock in the return circuit ( fig. 15, [4]).

8.2.7 Installing a pressure relief valve

▶ Install a 4-bar pressure relief valve ( fig. 15, [6]) with a minimum

passage of 22 mm in the flow circuit. Make sure that the pressure

relief valve is always installed between the boiler and the isolating

valve, so that the boiler will always be in contact with the pressure

relief valve, even if the isolating valves are closed.

8.2.8 Selecting and installing the pump

▶ Select a pump according to the hydraulic boiler resistance specified

in table 5 or in the curve in fig. 122 on page 62.

▶ When using the curve take the nominal required volume flow into

consideration according to table 3.

▶ When selecting the pump, take the maximum volume flow of the

boiler according to table 4 into consideration.

When using plastic pipes, observe the supplier’s

instructions - especially those referring to

recommended jointing techniques and the notes relating

to the heating system water on page 6

NOTICE:

To prevent contamination in the heating system we

recommend you to integrate a dirt filter [10] in the

return pipe, near the boiler. In an old system it is a

requirement to install a dirt filter.

▶ Install shut-off valves to enable filter cleaning

immediately upstream and downstream of the dirt

filter.

G1”

R1”

6 720 648 726-014.1TD

CAUTION: Damage to the installation.

The pressure in the heating system can become

excessively high.

▶ Install a pressure relief valve.

3 3

6 720 648 726-015.1TD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch GB162-80 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worcester-Bosch GB162-80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info